WinEMP - NRI

More documents

Recommendations

Info

INSTALLATION Connect laptop and card reader G-19.0656 on site 18 WinEMP – G-13.mft Connect the laptop and the card reader to the G-13.mft installed in the machine according to the following connection plan: Fig. 1d: Connection plan for G-13.mft – on site (or in the workshop) 1 Please make sure that the DIL switches of the coin validator are in the desired positions (see separate instructions for the validator). 2 Use the 10-pole connecting cable of the card reader G-19.0656 (ECV interface) to connect the card reader to the PCB direct plug on the right-hand side of the coin validator first. 3 Then use the interface labelled "USB PC" and the enclosed connecting cable to connect the card reader to a USB interface on the laptop. If the G-13.mft is not configured on site and powered by the machine, it can be supplied and configured using the card reader interface labelled with "12V DC" and the 12V-power pack enclosed in the WinEMP scope of delivery. National Rejectors, Inc. GmbH, Buxtehude
WinEMP – G-13.mft Start WinEMP National Rejectors, Inc. GmbH, Buxtehude INSTALLATION The easiest way to open the program is by • double-clicking on the WinEMP icon on the desktop of your PC or • accessing the Windows START menu, PROGRAMS and WINEMP. You are informed of the loading progress of the connected G-13.mft’s device data by the loading window’s status-bar indicator (LOOKING FOR VALIDATOR, VALIDATOR FOUND – READING DEVICE DATA). Once the loading process has been completed, you are automatically taken to the main menu of the software. The WinEMP version, the device type of the connected G-13.mft and the activated memory block 0 or 1 (if available) are displayed in the upper program line. The card LED on the card reader G-19.0647 is red as long as the software is accessing the inserted chip card. As long as the card LED is illuminated in red, the chip card must not be pulled out or inserted. This can destroy the card! If the software is unable to make a connection with the G-13.mft, it probably has one of the following causes: • The device environment has not been connected 1 Abort loading operation via EXIT. 2 Follow the instructions included in the section "Install device environment for workshop (card reader G-19.0647)" or "Connect laptop and card reader G-19.0656 on site" in this chapter. 3 Start WinEMP again. • Connections or cables are defective 1 Abort loading operation via EXIT. 2 Follow the instructions included in the section "Install device environment for workshop (card reader G-19.0647)" or "Connect laptop and card reader G-19.0656 on site" in this chapter or replace accessories. 3 Start WinEMP again. 19
Page 1: Technical Documentation The configu
Page 4 and 5: TABLE OF CONTENTS 4 WinEMP - G-13.m
Page 6 and 7: TABLE OF CONTENTS 6 WinEMP - G-13.m
Page 9 and 10: WinEMP - G-13.mft GENERAL INFORMATI
Page 15 and 16: WinEMP - G-13.mft 3 Installation In
Page 17: WinEMP - G-13.mft INSTALLATION 7 Pl
Page 21 and 22: WinEMP - G-13.mft National Rejector
Page 23 and 24: WinEMP - G-13.mft General operating
Page 25 and 26: WinEMP - G-13.mft GENERAL PROGRAM S
Page 29 and 30: WinEMP - G-13.mft Perform tests Nat
Page 31 and 32: WinEMP - G-13.mft Select memory blo
Page 35 and 36: WinEMP - G-13.mft 8 Configuration N
Page 37 and 38: WinEMP - G-13.mft G-13.mft with MDB
Page 43 and 44: WinEMP - G-13.mft Teach coin types/
Page 47 and 48: WinEMP - G-13.mft CONFIGURATION - F
Page 69 and 70:
WinEMP - G-13.mft CONFIGURATION - F
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
WinEMP - G-13.mft Copy and paste or
Page 117 and 118:
WinEMP - G-13.mft Change token/coin
Page 119 and 120:
WinEMP - G-13.mft National Rejector
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
WinEMP - G-13.mft After the data bl
Page 131 and 132:
Page 133 and 134:
WinEMP - G-13.mft 10 Restore G-13.m
Page 135 and 136:
WinEMP - G-13.mft WINEMP UPDATE 12
Page 137 and 138:
National Rejectors, Inc. GmbH, Buxt
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
WinEMP - G-13.mft C Card reader 10
Page 149 and 150:
WinEMP - G-13.mft E ECV 155 totaliz
Page 151 and 152:
WinEMP - G-13.mft Return signal lin
Page 153 and 154:
WinEMP - G-13.mft Glossary National
Page 155 and 156:
Page 157 and 158:
show all

WinEMP - NRI

Create successful ePaper yourself

Delete template?

Save as template?