WinEMP - NRI
WinEMP - NRI WinEMP - NRI
138 National Rejectors, Inc. GmbH, Buxtehude Error message Description Cause Remedy Main menu ERR12 - OPERATING VOLTAGE TOO HIGH ERR14 - CP4 SENSOR ACTIVE ERR16 - CP3 SENSOR ACTIVE ERR17 - CP SENSOR(S) ACTIVE DUE TO EXTERNAL LIGHT ERR27 - ENFORCED BREAK DUE TO STRING RECOGNITION ERR32 - LS SENSOR(S) ACTIVE DUE TO EXTERNAL LIGHT No signal from accepted coin sensor (CP4 sensor) No signal from accepted coin sensor (CP3 sensor) Continuous signal on one or both CP sensors Coin acceptance inhibited for 30 seconds following string manipulation Continuous signal on one or both CP sensors of the optical diameter measurement system (LS1/LS2) Operating voltage > 18 V CP4 sensor blocked or soiled CP4 sensor defective CP3 sensor blocked or soiled CP3 sensor defective External light disturbs sensor(s) Sensor(s) defective Free CP4 sensor from foreign particles or clean Replace CP4 sensor (service) Free CP3 sensor from foreign particles or clean Replace CP3 sensor (service) Install printed-circuit board cover Check sensor(s) (service) CP4 sensor became active at rest Wait 30 seconds or perform power-on reset External light disturbs sensor(s) Sensor(s) defective Install printed-circuit board cover Check sensor(s) (service) STATUS AND ERROR MESSAGES WinEMP – G-13.mft
National Rejectors, Inc. GmbH, Buxtehude 139 Error message Description Cause Remedy Main menu ERR33 - PILE-UP IN COIN RUNWAY ERR36 - RETURN LEVER PRESSED ERR39 - COIL DEFECTIVE ERR40 - COIL DEFECTIVE ERR41 - COIL DEFECTIVE ERR64 - COIN TOO QUICKLY INSERTED ERR65 - COIN TOO QUICKLY INSERTED Measurement area blocked Coin or foreign particle in coin runway Coin runway soiled Flight deck is open or was opened Interval between inserted coins too small Interval between inserted coins too small Return lever is being pressed or was pressed Coins following one another too closely in the measurement area Coins following one another too closely in the measurement area Remove coin or foreign particle Clean the flight deck (see separate instructions for the coil validator) Release return lever Check measuring system (service) Check measuring system (service) Check measuring system (service) Insert coins at greater intervals Insert coins at greater intervals WinEMP – G-13.mft STATUS AND ERROR MESSAGES
- Page 87 and 88: WinEMP - G-13.mft CONFIGURATION - F
- Page 89 and 90: WinEMP - G-13.mft CONFIGURATION - F
- Page 91 and 92: WinEMP - G-13.mft CONFIGURATION - F
- Page 93 and 94: WinEMP - G-13.mft CONFIGURATION - F
- Page 95 and 96: WinEMP - G-13.mft CONFIGURATION - F
- Page 97 and 98: WinEMP - G-13.mft CONFIGURATION - F
- Page 99 and 100: WinEMP - G-13.mft CONFIGURATION - F
- Page 101 and 102: WinEMP - G-13.mft CONFIGURATION - F
- Page 103 and 104: WinEMP - G-13.mft CONFIGURATION - F
- Page 105 and 106: WinEMP - G-13.mft CONFIGURATION - F
- Page 107 and 108: WinEMP - G-13.mft CONFIGURATION - F
- Page 109 and 110: WinEMP - G-13.mft CONFIGURATION - F
- Page 111 and 112: WinEMP - G-13.mft CONFIGURATION - F
- Page 113 and 114: WinEMP - G-13.mft CONFIGURATION - F
- Page 115 and 116: WinEMP - G-13.mft Copy and paste or
- Page 117 and 118: WinEMP - G-13.mft Change token/coin
- Page 119 and 120: WinEMP - G-13.mft National Rejector
- Page 121 and 122: WinEMP - G-13.mft National Rejector
- Page 123 and 124: WinEMP - G-13.mft National Rejector
- Page 125 and 126: WinEMP - G-13.mft National Rejector
- Page 127 and 128: WinEMP - G-13.mft National Rejector
- Page 129 and 130: WinEMP - G-13.mft After the data bl
- Page 131 and 132: WinEMP - G-13.mft National Rejector
- Page 133 and 134: WinEMP - G-13.mft 10 Restore G-13.m
- Page 135 and 136: WinEMP - G-13.mft WINEMP UPDATE 12
- Page 137: National Rejectors, Inc. GmbH, Buxt
- Page 141 and 142: National Rejectors, Inc. GmbH, Buxt
- Page 143 and 144: National Rejectors, Inc. GmbH, Buxt
- Page 145 and 146: National Rejectors, Inc. GmbH, Buxt
- Page 147 and 148: WinEMP - G-13.mft C Card reader 10
- Page 149 and 150: WinEMP - G-13.mft E ECV 155 totaliz
- Page 151 and 152: WinEMP - G-13.mft Return signal lin
- Page 153 and 154: WinEMP - G-13.mft Glossary National
- Page 155 and 156: WinEMP - G-13.mft National Rejector
- Page 157 and 158: WinEMP - G-13.mft National Rejector
National Rejectors, Inc. GmbH, Buxtehude<br />
139<br />
Error message Description Cause Remedy<br />
Main menu<br />
ERR33 -<br />
PILE-UP IN COIN RUNWAY<br />
ERR36 -<br />
RETURN LEVER PRESSED<br />
ERR39 -<br />
COIL DEFECTIVE<br />
ERR40 -<br />
COIL DEFECTIVE<br />
ERR41 -<br />
COIL DEFECTIVE<br />
ERR64 -<br />
COIN TOO QUICKLY<br />
INSERTED<br />
ERR65 -<br />
COIN TOO QUICKLY<br />
INSERTED<br />
Measurement area blocked Coin or foreign particle in coin runway<br />
Coin runway soiled<br />
Flight deck is open or was<br />
opened<br />
Interval between inserted coins<br />
too small<br />
Interval between inserted coins<br />
too small<br />
Return lever is being pressed or was<br />
pressed<br />
Coins following one another too closely<br />
in the measurement area<br />
Coins following one another too closely<br />
in the measurement area<br />
Remove coin or foreign particle<br />
Clean the flight deck (see separate<br />
instructions for the coil validator)<br />
Release return lever<br />
Check measuring system (service)<br />
Check measuring system (service)<br />
Check measuring system (service)<br />
Insert coins at greater intervals<br />
Insert coins at greater intervals<br />
<strong>WinEMP</strong> – G-13.mft STATUS AND ERROR MESSAGES