WinEMP - NRI
WinEMP - NRI WinEMP - NRI
136 National Rejectors, Inc. GmbH, Buxtehude 13 Status and error messages Error message Description Cause Remedy General NO VALIDATOR CONNECTED WinEMP is searching for a connected coin validator and does not find one NO ACCESS RIGHTS Selecting a function not possible ERROR WHEN SWITCHING THE BLOCK PLEASE RETURN TO THE MAIN MENU FIRST! – FOR THIS CLICK ON OK AND THEN ON BACK Desired memory (block) is not activated In the screen "Settings", WinEMP cannot be exited using X in the upper program line Device environment not completely connected Cables or connections defective Wrong serial PC interface selected (WinEMP searches for device at first available interface) Chip card inserted does not provide access authorization WinEMP cannot read data from selected memory (block) Security when reading in and reading out the device data Connect device environment (see Chap. 3 ”Installation”) Check cables or connections and replace, if necessary Select COM port to which the device environment is connected (see Chap. 3 ”Installation”) Repeat process with appropriately programmed chip card Terminate WinEMP (see Chap. 11 "Exit program"), restart (see Chap. 3 "Installation") and repeat process Exit the screen "Settings" first using BACK and then terminate WinEMP (see Chap. 11 ”Exit program”) STATUS AND ERROR MESSAGES WinEMP – G-13.mft
National Rejectors, Inc. GmbH, Buxtehude 137 Error message Description Cause Remedy Main menu ERR1 – 2 COINS IN MEASUREMENT AREA ERR4 - COIN TOO QUICKLY INSERTED ERR5 - COIN TOO QUICKLY INSERTED ERR6 - COIN TOO QUICKLY INSERTED ERR7 - OPERATING VOLTAGE TOO LOW 2 coins in measurement area at the same time, could not be checked Coin was rejected because previously accepted coin has not passed the accepted coin sensor Coin was rejected because coin signal of previously accepted coin has not been transmitted Coin was rejected because sorting of previously accepted coin has not been completed Coins following one another too closely Insert coins at greater intervals Coins following one another too closely Insert coins at greater intervals Coins following one another too closely Insert coins at greater intervals Coins following one another too closely Insert coins at greater intervals Operating voltage < 8.5 V WinEMP – G-13.mft STATUS AND ERROR MESSAGES
- Page 85 and 86: WinEMP - G-13.mft CONFIGURATION - F
- Page 87 and 88: WinEMP - G-13.mft CONFIGURATION - F
- Page 89 and 90: WinEMP - G-13.mft CONFIGURATION - F
- Page 91 and 92: WinEMP - G-13.mft CONFIGURATION - F
- Page 93 and 94: WinEMP - G-13.mft CONFIGURATION - F
- Page 95 and 96: WinEMP - G-13.mft CONFIGURATION - F
- Page 97 and 98: WinEMP - G-13.mft CONFIGURATION - F
- Page 99 and 100: WinEMP - G-13.mft CONFIGURATION - F
- Page 101 and 102: WinEMP - G-13.mft CONFIGURATION - F
- Page 103 and 104: WinEMP - G-13.mft CONFIGURATION - F
- Page 105 and 106: WinEMP - G-13.mft CONFIGURATION - F
- Page 107 and 108: WinEMP - G-13.mft CONFIGURATION - F
- Page 109 and 110: WinEMP - G-13.mft CONFIGURATION - F
- Page 111 and 112: WinEMP - G-13.mft CONFIGURATION - F
- Page 113 and 114: WinEMP - G-13.mft CONFIGURATION - F
- Page 115 and 116: WinEMP - G-13.mft Copy and paste or
- Page 117 and 118: WinEMP - G-13.mft Change token/coin
- Page 119 and 120: WinEMP - G-13.mft National Rejector
- Page 121 and 122: WinEMP - G-13.mft National Rejector
- Page 123 and 124: WinEMP - G-13.mft National Rejector
- Page 125 and 126: WinEMP - G-13.mft National Rejector
- Page 127 and 128: WinEMP - G-13.mft National Rejector
- Page 129 and 130: WinEMP - G-13.mft After the data bl
- Page 131 and 132: WinEMP - G-13.mft National Rejector
- Page 133 and 134: WinEMP - G-13.mft 10 Restore G-13.m
- Page 135: WinEMP - G-13.mft WINEMP UPDATE 12
- Page 139 and 140: National Rejectors, Inc. GmbH, Buxt
- Page 141 and 142: National Rejectors, Inc. GmbH, Buxt
- Page 143 and 144: National Rejectors, Inc. GmbH, Buxt
- Page 145 and 146: National Rejectors, Inc. GmbH, Buxt
- Page 147 and 148: WinEMP - G-13.mft C Card reader 10
- Page 149 and 150: WinEMP - G-13.mft E ECV 155 totaliz
- Page 151 and 152: WinEMP - G-13.mft Return signal lin
- Page 153 and 154: WinEMP - G-13.mft Glossary National
- Page 155 and 156: WinEMP - G-13.mft National Rejector
- Page 157 and 158: WinEMP - G-13.mft National Rejector
National Rejectors, Inc. GmbH, Buxtehude<br />
137<br />
Error message Description Cause Remedy<br />
Main menu<br />
ERR1 –<br />
2 COINS IN MEASUREMENT<br />
AREA<br />
ERR4 -<br />
COIN TOO QUICKLY<br />
INSERTED<br />
ERR5 -<br />
COIN TOO QUICKLY<br />
INSERTED<br />
ERR6 -<br />
COIN TOO QUICKLY<br />
INSERTED<br />
ERR7 -<br />
OPERATING VOLTAGE TOO<br />
LOW<br />
2 coins in measurement area at<br />
the same time, could not be<br />
checked<br />
Coin was rejected because<br />
previously accepted coin has<br />
not passed the accepted coin<br />
sensor<br />
Coin was rejected because coin<br />
signal of previously accepted<br />
coin has not been transmitted<br />
Coin was rejected because<br />
sorting of previously accepted<br />
coin has not been completed<br />
Coins following one another too closely Insert coins at greater intervals<br />
Coins following one another too closely Insert coins at greater intervals<br />
Coins following one another too closely Insert coins at greater intervals<br />
Coins following one another too closely Insert coins at greater intervals<br />
Operating voltage < 8.5 V<br />
<strong>WinEMP</strong> – G-13.mft STATUS AND ERROR MESSAGES