WinEMP - NRI
WinEMP - NRI WinEMP - NRI
CONFIGURATION – FOR MDB/S1 INTERFACE Deactivate/activate teach mode 100 WinEMP – G-13.mft The G-13.mft is usually delivered so that you can teach new tokens or coin types on site on the vending machine in the last eight coin channels (teach channels). You can either fully deactivate this teach function or make it possible for fewer coin channels to prevent, if necessary, any teach channels assigned to important coin types from being overwritten unintentionally. If you want to change teach mode settings: 1 Select menu item EXTRA and then OPTIONS. The dialog box BASIC SETTINGS AND OPTIONS opens. In the "table of contents" on the left-hand side, the index word TEACH MODE has already been selected. To deactivate the function: 2a On the righthand side, click TEACH MODE (remove tick). Clicking again would set the tick again and activate the teach mode. To limit the function to specific teach channels: 2b On the right-hand side under ACTIVATE TEACH CHANNELS click (tick) the box of the channel number(s) that is (are) to be enabled on site for the teaching process. Clicking again would delete the tick and inhibit the channel for the teach mode. 3 Confirm your entry with OK and close the window again or proceed to the next setting in this dialog box first and confirm all your settings later. 4 Click BACK to store the setting in the G-13.mft or proceed to the next setting on this screen and store all your settings later. National Rejectors, Inc. GmbH, Buxtehude
WinEMP – G-13.mft CONFIGURATION – FOR MDB/S1 INTERFACE Configure sorting If an external sorting device was connected to the coin validator, the following settings must be performed in WinEMP: • which sorting control line or which sorting way is to be used to control a sorting chute for the purpose of sorting a specific coin and • how long the sorting control line(s) is (are) to be controlled. Since the control system with external sorting of the G-13.mft with MDB interface differs from the one of the G-13.mft with S1 interface, the configuration is dealt with in separate sections. Assign sorting control line to a coin type (only for G-13.mft with MDB interface) If an external sorting device is connected to the coin validator, you can assign the coin types to be sorted one of three sorting control lines. 1 In the line of the respective coin channel under the heading "SORT 3 2 1" tick the desired sorting control line 1–3 by clicking on the box and, if necessary, 2 remove the tick set under any other line by clicking the box. 3 Click BACK to store the setting in the G-13.mft or proceed to the next setting on this screen and store all your settings later. National Rejectors, Inc. GmbH, Buxtehude 101
- Page 49 and 50: WinEMP - G-13.mft CONFIGURATION - F
- Page 51 and 52: WinEMP - G-13.mft CONFIGURATION - F
- Page 53 and 54: WinEMP - G-13.mft CONFIGURATION - F
- Page 55 and 56: WinEMP - G-13.mft CONFIGURATION - F
- Page 57 and 58: WinEMP - G-13.mft CONFIGURATION - F
- Page 59 and 60: WinEMP - G-13.mft CONFIGURATION - F
- Page 61 and 62: WinEMP - G-13.mft CONFIGURATION - F
- Page 63 and 64: WinEMP - G-13.mft CONFIGURATION - F
- Page 65 and 66: WinEMP - G-13.mft CONFIGURATION - F
- Page 67 and 68: WinEMP - G-13.mft CONFIGURATION - F
- Page 69 and 70: WinEMP - G-13.mft CONFIGURATION - F
- Page 71 and 72: WinEMP - G-13.mft CONFIGURATION - F
- Page 73 and 74: WinEMP - G-13.mft CONFIGURATION - F
- Page 75 and 76: WinEMP - G-13.mft CONFIGURATION - F
- Page 77 and 78: WinEMP - G-13.mft CONFIGURATION - F
- Page 79 and 80: WinEMP - G-13.mft CONFIGURATION - F
- Page 81 and 82: WinEMP - G-13.mft CONFIGURATION - F
- Page 83 and 84: WinEMP - G-13.mft CONFIGURATION - F
- Page 85 and 86: WinEMP - G-13.mft CONFIGURATION - F
- Page 87 and 88: WinEMP - G-13.mft CONFIGURATION - F
- Page 89 and 90: WinEMP - G-13.mft CONFIGURATION - F
- Page 91 and 92: WinEMP - G-13.mft CONFIGURATION - F
- Page 93 and 94: WinEMP - G-13.mft CONFIGURATION - F
- Page 95 and 96: WinEMP - G-13.mft CONFIGURATION - F
- Page 97 and 98: WinEMP - G-13.mft CONFIGURATION - F
- Page 99: WinEMP - G-13.mft CONFIGURATION - F
- Page 103 and 104: WinEMP - G-13.mft CONFIGURATION - F
- Page 105 and 106: WinEMP - G-13.mft CONFIGURATION - F
- Page 107 and 108: WinEMP - G-13.mft CONFIGURATION - F
- Page 109 and 110: WinEMP - G-13.mft CONFIGURATION - F
- Page 111 and 112: WinEMP - G-13.mft CONFIGURATION - F
- Page 113 and 114: WinEMP - G-13.mft CONFIGURATION - F
- Page 115 and 116: WinEMP - G-13.mft Copy and paste or
- Page 117 and 118: WinEMP - G-13.mft Change token/coin
- Page 119 and 120: WinEMP - G-13.mft National Rejector
- Page 121 and 122: WinEMP - G-13.mft National Rejector
- Page 123 and 124: WinEMP - G-13.mft National Rejector
- Page 125 and 126: WinEMP - G-13.mft National Rejector
- Page 127 and 128: WinEMP - G-13.mft National Rejector
- Page 129 and 130: WinEMP - G-13.mft After the data bl
- Page 131 and 132: WinEMP - G-13.mft National Rejector
- Page 133 and 134: WinEMP - G-13.mft 10 Restore G-13.m
- Page 135 and 136: WinEMP - G-13.mft WINEMP UPDATE 12
- Page 137 and 138: National Rejectors, Inc. GmbH, Buxt
- Page 139 and 140: National Rejectors, Inc. GmbH, Buxt
- Page 141 and 142: National Rejectors, Inc. GmbH, Buxt
- Page 143 and 144: National Rejectors, Inc. GmbH, Buxt
- Page 145 and 146: National Rejectors, Inc. GmbH, Buxt
- Page 147 and 148: WinEMP - G-13.mft C Card reader 10
- Page 149 and 150: WinEMP - G-13.mft E ECV 155 totaliz
CONFIGURATION – FOR MDB/S1 INTERFACE<br />
Deactivate/activate teach mode<br />
100<br />
<strong>WinEMP</strong> – G-13.mft<br />
The G-13.mft is usually delivered so that you can teach new tokens or coin<br />
types on site on the vending machine in the last eight coin channels (teach<br />
channels). You can either fully deactivate this teach function or make it<br />
possible for fewer coin channels to prevent, if necessary, any teach<br />
channels assigned to important coin types from being overwritten<br />
unintentionally.<br />
If you want to change teach mode settings:<br />
1 Select menu item EXTRA and then OPTIONS.<br />
The dialog box BASIC SETTINGS AND OPTIONS opens. In the "table of<br />
contents" on the left-hand side, the index word TEACH MODE has<br />
already been selected.<br />
To deactivate the function:<br />
2a On the righthand<br />
side,<br />
click TEACH<br />
MODE (remove<br />
tick).<br />
Clicking again<br />
would set the<br />
tick again and<br />
activate the<br />
teach mode.<br />
To limit the function to specific teach channels:<br />
2b On the right-hand side under ACTIVATE TEACH CHANNELS click (tick) the<br />
box of the channel number(s) that is (are) to be enabled on site for<br />
the teaching process.<br />
Clicking again would delete the tick and inhibit the channel for the<br />
teach mode.<br />
3 Confirm your entry with OK and close the window again or proceed<br />
to the next setting in this dialog box first and confirm all your settings<br />
later.<br />
4 Click BACK to store the setting in the G-13.mft or proceed to the next<br />
setting on this screen and store all your settings later.<br />
National Rejectors, Inc. GmbH, Buxtehude