Premier 48, 88, 168 & 640 Installation Manual - PVK

More documents

Recommendations

Info

Programming the Control Panel Premier 48, 88, 168 & 640 Installation Manual 60 - Armed/Alarm This output type activates when the selected area is armed and deactivates when the selected area is disarmed This output type also pulses when an Intruder alarm occurs in the selected area, and deactivates when the selected area is disarmed. 61 - Intruder Alarm This output type activates when an Intruder alarm occurs, and deactivates when the Intruder alarm is cancelled. Tamper alarms will not activate this output 62 - Speaker Mimic This output type activates whenever the internal speaker output is on, and deactivates when the speaker output is off. Output Group - Zone Any zone can be assigned to this output type. Select a zone number from 1 to 48 (Premier 48), 1 to 88 (Premier 88) or 1 to 168 (Premier 168).then select an output type from the following options: Mimic This output type activates when the selected zone is activated and deactivates when the zone is secure. This output will work if the zone is armed or disarmed. MimicArm This output type activates when the selected zone is activated and deactivates when the zone is secured. This output will only work if the zone is armed. Alarm This output type activates when the selected zone causes an alarm and deactivates when the alarm is reset. This output will only work if the zone is armed. Tamper This output type activates when the selected zone causes a Tamper alarm and deactivates when the tamper is reset. This output will work if the zone is armed or disarmed. MimicLat This output type activates when the selected zone is activated and deactivates when the next time the zone is activated. This output will work if the zone is armed or disarmed. Omitted This output type activates when the selected zone is omitted and deactivates when the zone is reinstated. Output Group - User Code Entered Any user can be assigned to this output type. Select a user number from 1 to 25 (Premier 48), 1 to 50 (Premier 88) or 1 to 99 (Premier 168). This output type activates for 5 seconds when the selected User code is entered. Output Group - Control Timer Select a Control Timer from 1 to 4 (Premier 48) or 1 to 8 (Premier 88/168). These output types activate when the respective control timer turns on and deactivate when the timer turns off. Output Group - PC Control Select a PC Control from 1 to 4 (Premier 48), 1 to 8 (Premier 88/168/640). These output types can be activated and deactivated using a PC running the Wintex UDL software. Output Group - Door Control Select a Door Control from 1,1 to 1,4 (Premier 48), 1,1 to 1,8 (Premier 88), 1,1 to 2,8 (Premier 168) or 1,1 to 8,8 (Premier 640). These output types activate for the duration of the ‘Door Strike’ timer when a valid User code (assigned to the same door) is entered and deactivates when the timer expires. These output types are used in conjunction with the ‘Door Control’ User option (see page 83 for details). Output Attributes Assigning an attribute to an output will alter how the output works. The following attributes can be assigned to any of the various types listed. Select attributes by pressing keys 1 to 8 (a letter on the display means the attribute is selected, a ‘Dot’ on the display means the attribute is not selected). U - User Test The output will activate when a user performs a User test (see page 87 for details). I - Inverted The output is inverted (an output that applies 0V when active will become an output that applies 12V when active). L - Latching When activated, the output will remain on until a valid User code is entered. 1 - Use Pulse Period 1 When activated, the output will remain on for the duration of the ‘Pulse Period 1’ timer (see page 44 for details). 2 - Use Pulse Period 2 When activated, the output will remain on for the duration of the ‘Pulse Period 2’ timer (see page 44 for details). 3 - Use Pulse Period 3 When activated, the output will remain on for the duration of the ‘Pulse Period 3’ timer (see page 44 for details). C - Only Active With Custom Output 1 Stage A The output will only operate whilst ‘Custom Output Stage A’ is ‘On’ (see page ‘Custom Outputs’ for details). R - Random The output will activate randomly. A minimum and maximum ‘On’ time can also be programmed (see page 44 for details). 62 INS176
Premier 48, 88, 168 & 640 Installation Manual Programming the Control Panel Custom Outputs Custom outputs are NOT physical outputs they are ‘Software outputs that can be configured to operate under certain conditions. Once configured these outputs can then be assigned to a physical output (see system outputs 22-27 and 32-37, page 59 for details). Custom Output 1 - 4, Stage A Will activate when switches 1 or 2 and 3 and 4 are active. Custom Output 1 - 4, Stage B Will activate when switches 5 or 6 and 7 and 8 are active. Custom Output 1 - 4, Stage AB Will activate when switches 1 or 2 and 3 and 4 are active OR switches 5 or 6 and 7 and 8 are active. 1 2 5 6 3 4 7 8 Example Switch 1 is programmed as: Zone 1 Mimic Switch 2 is programmed as: Zone 2 Mimic Switch 3 is programmed as: Armed Switch 4 is programmed as: Never Active (and inverted) A AB Custom Output 1 Stage A will only activate when switches 1 OR 2 AND 3 AND 4 are closed. i.e. if ZONE 1 or ZONE 2 ACTIVATES whilst the system is ARMED (switch 4 is always closed). B X-10 Outputs X-10 Outputs are outputs that can be configured to operate devices that are connected to an X-10 controller. These outputs can be assigned a house and unit number. To Program an output for X-10, proceed as follows: Program the output type to ensure correct operation when the programmed condition occurs i.e. an output programmed as ‘Entry/Exit’ will activate when the selected area is in the entry or exit mode and deactivate when the area is no longer in the entry or exit mode. Assign any attributes i.e. ‘Pulsed 1’ would cause the output to be timed for the duration of the ‘Pulse 1’ timer. Assign a House and Unit number i.e. this is the physical address of the X-10 Unit and ensures that the correct unit in the correct area operates when the output condition is met i.e the correct unit switches on and off during Entry/Exit. Assign up to 16 Characters of text to each unit to allow easy identification when the output needs to be manually triggered directly from the keypad using the command i.e. ‘Entrance Light’. INS176 63
Page 1 and 2:
THANK YOU FOR VOTING TEXECOM INSTAL
Page 3 and 4:
Contents Premier 48, 88, 168 & 640
Page 5 and 6:
Premier 48, 88, 168 & 640 Installat
Page 7 and 8:
Page 9 and 10:
Page 11 and 12: Premier 48, 88, 168 & 640 Installat
Page 29 and 30: Premier 48, 88 & 168 Installation M
Page 61: Premier 48, 88, 168 & 640 Installat
show all

Premier 48, 88, 168 & 640 Installation Manual - PVK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?