Premier 48, 88, 168 & 640 Installation Manual - PVK

More documents

Recommendations

Info

System Overview Premier 48, 88, 168 & 640 Installation Manual Other Devices PC-Com • For connecting a PC to the control panel via an RS232 Serial port allowing local uploading and downloading using Wintex UDL software USB-Com • For connecting a PC to the control panel via a USB 1.0 or 2.0 port allowing local uploading and downloading using Wintex UDL software UNI-Com • For connecting a serial device i.e. PC modem or mobile phone to the control panel PRINT-Com • For connecting a serial printer to the control panel RPD-Com • For connecting a RP9 Radio-Pad to the control panel GSM-Com • For connecting a GSM Module to the control panel 6 INS176
Premier 48, 88, 168 & 640 Installation Manual Installation 2. Installation Installation Sequence Before attempting to install the alarm system, read this section. Once you have an overall understanding of the installation sequence, carefully work through each step. 1: Design the Layout Make a rough sketch of the premises to get an idea of where the alarm detection devices, keypads, zone expanders etc. are to be located. 2: Mounting the Panel The control panel should be mounted in a dry area close to an unswitched AC power source and the incoming telephone line (if using a communicator). You must complete all wiring before connecting the battery or applying AC mains to the control panel. 3: Install the Keypads and Zone Expanders Mount and connect the keypads, zone expanders and output modules to the control panel (see page 12 for wiring details). 4: Install the Alarm Detection Devices Install the detection devices, PIR’s, Contacts, PA Buttons etc. and connect them to the control panel (see page 19 for wiring details). 5: Install the External Sounder Install the external sounder and connect to the control panel (see page 20 for wiring details). 6: Other Wiring Complete all other wiring including speakers, telephone line and output connections etc. (see pages 20 - 21 for details). 7: Applying Power to the Control Panel Once steps 1 to 6 are completed, power can be applied to the control panel. When applying power for the first time, the factory default settings must be loaded (see page 25 for details). Power should always be connected in the following order: • Connect the red battery lead to the positive terminal of the battery and then connect the black battery lead to the negative terminal The panel will only become ‘live’ when the AC Mains is connected or the ‘Battery Kick-start’ button is pressed. • Connect the AC mains For a complete list of factory default settings, see page 28. 8: Programming the Control Panel Please refer to section 5 for instruction on programming the control panel. 9: Testing the System Test the system thoroughly to ensure that all features and functions operate as required (see page 84 for details). Control Panel Mounting Mount the control panel on a flat, plumb wall using at least three screws of appropriate size. INS176 7 It is essential to ensure that none of the fixing slots or cable entries are accessible after fixing. Mains cabling must be secured (e.g. with a cable tie) to one of the anchor points provided. Wiring the Control Panel WARNING: ELECTRICITY CAN KILL BEFORE connecting the control panel ALWAYS disconnect the supply at the consumer unit. If in ANY doubt consult a qualified electrician. IMPORTANT SAFETY INFORMATION. HAZARDOUS VOLTAGES INSIDE, NO USER SERVICEABLE PARTS, NO USER ACCESS. ONLY connect the mains supply to the mains terminal block, NEVER connect the mains supply directly to the PCB. ALWAYS refer to National Wiring Regulations when conducting installation. An appropriate and readily accessible disconnection device (e.g. an unswitched fused spur) MUST be provided as part of the installation. The disconnection device must NOT be fitted in a flexible cord. Where identification of the neutral in the mains supply is NOT possible a two-pole disconnection device MUST be used. The building mains supply MUST incorporate appropriate short-circuit backup protection (e.g. a fuse or circuit breaker) of High Breaking Capacity (HBC, at least 1500A). Use mains cable of adequate carrying capacity for the rated current (i.e. at least 0.75mm 2 ).
Page 1 and 2: THANK YOU FOR VOTING TEXECOM INSTAL
Page 3 and 4: Contents Premier 48, 88, 168 & 640
Page 5: Premier 48, 88, 168 & 640 Installat
Page 9 and 10: Premier 48, 88, 168 & 640 Installat
Page 29 and 30: Premier 48, 88 & 168 Installation M
Page 57 and 58:
Premier 48, 88, 168 & 640 Installat
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
show all

Premier 48, 88, 168 & 640 Installation Manual - PVK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?