Premier 48, 88, 168 & 640 Installation Manual - PVK

More documents

Recommendations

Info

Programming the Control Panel Premier 48, 88, 168 & 640 Installation Manual Attributes for Moment or Latch Keys Select attributes by pressing keys 1 to 8 (a letter on the display means the attribute is selected, a Dot on the display means the attribute is not selected). The following attributes are only available for ‘Moment Key’ or ‘Latch Key’ zone types. I - INSTANT ARM When using a key switch, the area will arm instantly. P - PART ARMING When using a key switch, the area will ‘Part’ arm. F – FULL ARM DISABLE When using a key switch to ‘Full’ arm an area, the key switch is disabled once the area is armed. D - DISARM ONLY The key switch cannot be used for ‘Arming’ (it can only be used for ‘Disarming’). F - SILENTARMING When arming using a key switch, the selected areas will arm silently. T - TIME ARM DISABLE Activation of the key switch will override the ‘Time Arming’ feature on the control panel and prevent it from operating until the zone is reinstated. K - KEY TUBE A key switch zone type with this attribute will log when the zone is activated and also when the zone is restored. Attributes for Custom Zones Select attributes by pressing keys 1 to 8 (a letter on the display means the attribute is selected, a Dot on the display means the attribute is not selected). The following attributes are only available for ‘Custom’ zone types. I - INTERNAL Activation of this zone (when armed) will cause the internal sounders to activate. B - BELL/STROBE Activation of this zone (when armed) will cause the external sounder/strobe to activate. M - MONITOR 24Hr The zone is armed at all times. C - ENABLE COMS Activation of this zone (when armed) will cause the area ‘Alarm’ output to activate. Any Custom zone with this attribute will activate both the internal and external sounders even if they are not enabled above. W - WARNING REQ. If the zone remains Active for the duration of the ‘Warning Delay’ timer (see page 45), a warning tone will occur every 30 seconds for 3 minutes (or until a code is entered or is pressed). If MONITOR 24Hr is enabled, an internal alarm will occur after the Warning Delay. Zone Areas The Premier 48 can be divided into four separate areas of protection, the Premier 88 can be divided into eight separate areas of protection and the Premier 168 and 640 can be divided into sixteen separate areas of protection. This allows different parts of a building to be armed and disarmed independently from each other. By default all zones are assigned to area A, but if required, a zone can be assigned to any number of areas. 36 INS176 If a zone is assigned to more than one area, it will only be recognised by the system when all areas it is assigned to, are armed. After entering a zone number (step 3), pressing AREA will jump straight to the ‘Zone Areas’ Zone Text Each zone can have up to 32 characters of descriptive text assigned to it. Text is programmed in a similar way to mobile phones. Select characters by pressing the corresponding key the appropriate number of times (to select a character on the same key, press to move the cursor along). For a more information, see page 32. The control panel also features Predictive text. This can be used to make inserting words easier, i.e. when spelling the word PIR, instead of typing 7444777, all that you need to do is type 747 and the word is automatically selected. This feature can be turned on and off as required by pressing the key and can also be automatically selected every time text mode is entered (see page 46 for details). DD 243 To comply with DD 243, during the normal entry delay, the control panel must prevent a Confirmed Intruder Alarm from being reported to the Alarm Receiving Centre. If a Portable ACE i.e. Electronic Keyswitch, Key Fob, Tag, Swipe Card etc. is being used for disarming, it is permissible for the Confirmed Intruder Alarm signal to be re-enabled after the entry delay has expired. WARNING Owing to the ability to disable ALL of the confirmation facilities, the customer should be advised in writing by the alarm company that ALL means of alarm confirmation are disabled when the initial entry door is opened. The alarm company should then obtain written acceptance from the customer of the disabling of the means of alarm confirmation.
Premier 48, 88, 168 & 640 Installation Manual Programming the Control Panel 5.2 Area Programming Timers Yes Yes Reset Yes ??? Yes Use the SCROLL key to select an area Press YES to move to the required timer group or press RESET to move backwards e.g. YES Enter a new timer value e.g. 025 = 25 Seconds These groups of ‘Area’ timers control timing and delay functions for areas 1 – 4 (Premier 48), 1 - 8 (Premier 88) and 1 - 16 (Premier 168 and 640). Each timer can be programmed for any value between 000 and 999. 1 - Exit Delay- for Areas A to D (A to H) (A to P) When the area exit mode is programmed as ‘Timed’ this timer controls the delay between the user initiating the exit mode for the selected area and the area actually. 2 - Entry 1 Delay - for Areas A to D (A to H) (A to P) If the area is armed and an ‘Entry/Exit 1’ zone is activated, this timer will start and the entry tone will be heard. If the area is not disarmed before this timer expires, the ‘2nd Entry Delay’ timer will start. 3 - Entry 2 Delay - for Areas A to D (A to H) (A to P) If the area is armed and an ‘Entry/Exit 2’ zone is activated, this timer will start and the entry tone will be heard. If the area is not disarmed before this timer expires, the ‘2nd Entry Delay’ timer will start. 4 - 2nd Entry Dly - for Areas A to D (A to H) (A to P) When the area ‘Entry Delay 1 or 2’ timer expires, this timer will start and an Internal alarm will occur. If the area is still not disarmed before this timer expires, an Intruder alarm will then occur. 5 - Bell Delay - for Areas A to D (A to H) (A to P) This timer controls the delay between an Intruder alarm occurring in the selected area and the ‘Bell/Strobe’ output activating. 6 - Bell Duration - for Areas A to D (A to H) (A to P) This timer controls the duration of the ‘Bell’ output after an Intruder alarm has occurred in the selected area and any programmed ‘Bell Delay’ has expired. 7 - Coms Delay. for Areas A to D (A to H) (A to P) This timer controls the delay between an Intruder alarm occurring in the selected area and the communicator reporting to the Alarm Receiving Centre. 8 - Part Bell Dly. for Areas A to D (A to H) (A to P) When the selected area is ‘Part Armed’ this timer controls the delay between an Intruder alarm occurring in the selected area and the ‘Bell/Strobe’ output activating, the internal sounders will also sound during this time as a warning. INS176 37
Page 1 and 2: THANK YOU FOR VOTING TEXECOM INSTAL
Page 3 and 4: Contents Premier 48, 88, 168 & 640
Page 5 and 6: Premier 48, 88, 168 & 640 Installat
Page 29 and 30: Premier 48, 88 & 168 Installation M
Page 35: Premier 48, 88, 168 & 640 Installat
Page 87 and 88:
Premier 48, 88, 168 & 640 Installat
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
show all

Premier 48, 88, 168 & 640 Installation Manual - PVK

Create successful ePaper yourself

Delete template?

Save as template?