Premier 48, 88, 168 & 640 Installation Manual - PVK

More documents

Recommendations

Info

Installation Premier 48, 88, 168 & 640 Installation Manual Plug-on Communicators The Com300 is a multi format 8-channel digital communicator/300-baud modem for use with a standard analogue telephone line. The Com2400 is a multi format 8-channel digital communicator/2400-baud modem for use with a standard analogue telephone line in addition, this modem can also send Short Message Service (SMS) text messages to a mobile phone. The ComISDN is a multi format 8-channel digital communicator/modem for use with an ISDN telephone line. These Communicators can be used to report system events to an Alarm Receiving Centre using Fast Format, Contact ID or SIA Level II or to upload/download control panel information using the Wintex UDL software and a PC. Plugging on the Communicator Ensure that the board is the correct way up (see below). Locate the plug into the communicator socket on the control panel and line up the mounting holes with the pillars in the base. Once all the holes line up, press down gently until the pillars snap into the holes. Box Tam p Standard Telephone Line Connections A standard telephone line must be connected to the Com300 or Com2400 communicator as shown below: Master Socket T = 5 or A - White/Blue ring R = 2 or B - Blue/White ring Com300 T This terminal must be connected to the incoming AC Mains earth supply or R Com2400 T1 To other telephone R1 extension sockets 22 INS176 6 5 4 3 2 1 Telephone cable Type 1/0.5mm CW1308 ISDN Telephone Line Connections An ISDN telephone line must be connected to the ComISDN communicator as shown below: ISDN Terminal ComISDN RJ45 Lead For details on testing the communicators, see page 64.
Premier 48, 88, 168 & 640 Installation Manual Installation RP9 Radio-Pad Before connecting the Radio-Pad, isolate ALL power from the control panel (AC mains and battery), do not continue if there is still power present on the control panel. To install the Radio-Pad onto the control panel: • Connect the Molex connector of the RPD-Com lead to Com2 on the control panel • Connect the 25-Way D-Type connector of the RPD-Com to the Radio-Pad • Locate the power lead connector into the socket at the bottom of the Radio-Pad • Connect the Black lead to the DC- terminal on the control panel • Connect the lead with the White stripe to the DC+ terminal on the control panel • Follow the procedure for Registering the Radio-Pad Registering the Radio-Pad Whenever a Paknet Radio-Pad is installed or moved, it must be registered onto the network. To do this: • Press and hold the test button on the front of the Paknet Radio-Pad • With the test button still pressed, connect power to the control panel and wait for the yellow service light on the Radio-Pad to flash • Release the test button Within 2 minutes the yellow service light should stop flashing and remain steady. This means that the Paknet Radio-Pad has now selected and locked on to the Base Station with the strongest signal. The Paknet Radio-Pad should be re-registered on every site visit, this is to ensure that any new Vodafone Packet Radio Service Base Stations in the vicinity are recorded by the Paknet Radio-Pad. Programming the Radio-Pad • Program Com 2 for Radio-Pad operation (see page 73 for details) • Refer to the Radio-Pad installation guide for full programming details. GSM Module Before connecting the GSM Module, isolate ALL power from the control panel (AC mains and battery), do not continue if there is still power present on the control panel. To install the GSM Module onto the control panel: • Connect the Molex connector of the GSM-Com lead to Com2 on the control panel • Connect the RJ45 connector of the GSM-Com to the GSM Module • Locate the power Jack Plug into the socket at the bottom of the GSM Module • Insert a SIM card into the bottom of the GSM Module • Connect power to the control panel Programming the GSM Module • Program Com 2 for GSM Module operation (see page 73 for details) • Refer to the GSM Module installation guide for full programming details. AV Module Before connecting the AV Module, isolate ALL power from the control panel (AC mains and battery), do not continue if there is still power present on the control panel. To install the AV Module onto the control panel: • Connect one end of the patch lead on to the Expansion Port of the AV Module • Connect one other end of the patch lead on to the Expansion Port of the control panel Programming the AV Module • Program the Expansion Port for AV Module operation (see page 73 for details) • Refer to the AV Module installation guide for full programming details. ComIP Module Before connecting the ComIP Module, isolate ALL power from the control panel (AC mains and battery), do not continue if there is still power present on the control panel. To install the ComIP onto the control panel: • Connect one end of the patch lead on to JP1 of the ComIP • Connect one other end of the patch lead on to Com1 or 2 of the control panel Programming the ComIP Module • Program Com1 or 2 for ComIP Module operation (see page 73 for details) • Refer to the ComIP Module installation guide for full programming details. INS176 23
Page 1 and 2: THANK YOU FOR VOTING TEXECOM INSTAL
Page 3 and 4: Contents Premier 48, 88, 168 & 640
Page 5 and 6: Premier 48, 88, 168 & 640 Installat
Page 21: Premier 48, 88, 168 & 640 Installat
Page 29 and 30: Premier 48, 88 & 168 Installation M
Page 73 and 74:
Premier 48, 88, 168 & 640 Installat
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
show all

Premier 48, 88, 168 & 640 Installation Manual - PVK

Create successful ePaper yourself

Delete template?

Save as template?