Instructions for Use 3 mm - Varicor
Instructions for Use 3 mm - Varicor
Instructions for Use 3 mm - Varicor
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
3. GENERAL PROCESSING GUIDELINES<br />
3.9 SURFACE FINISH (FOLLOWING)<br />
Always use an excentric polisher and not a vibrating grinder <strong>for</strong> the<br />
surface finish. The grain sequences which we reco<strong>mm</strong>end are listed<br />
in the table below:<br />
Degree of gloss Festool* 3M* Jöst*<br />
Silky-matt Brilliant P 150 266 L, 100 micron Superpad P 150<br />
The best surface is the one, the end consumer can reproduce repeatedly.<br />
For surfaces subject to heavy use, we reco<strong>mm</strong>end a silky-matt finish.<br />
Reco<strong>mm</strong>end the cleaning milk which you use – and thus enable your<br />
customers to reproduce the surface finish which you created.<br />
3.10 BACK SPLASH<br />
Plastic profiles which are clipped into a screwed on plastic strip are reco<strong>mm</strong>endable<br />
as back splashes. Adhere the matching <strong>Varicor</strong> ® 3 <strong>mm</strong><br />
strip to the plastic profile with sealing lip. The plastic profiles are<br />
available in various colours.<br />
Please note that creating a back splash by gluing with the <strong>Varicor</strong> ®<br />
glue a 12 <strong>mm</strong> sheet on a sheet of 3 <strong>mm</strong> is not possible due to different<br />
expansion coefficients.<br />
3.11 WALL PANELLING<br />
Brilliant P 180 266 L, 80 micron Superpad P 220<br />
Brilliant P 240 266 L, 60 micron Superpad P 320<br />
Brilliant P 320 266 L, 30 micron Superpad P 400<br />
Brilliant P 400 Superpad SG 600<br />
Grinding mat<br />
Platinum S 800<br />
Apply cleansing milk.<br />
Polish by using<br />
excentric and felt disk<br />
High gloss as <strong>for</strong> silky-matt<br />
up to P 400<br />
Grinding mat<br />
Platinum S 800<br />
Apply cleansing milk.<br />
Polish by using<br />
excentric and felt disk<br />
as <strong>for</strong> silky-matt<br />
up to 30 micron<br />
Superpad SG 800<br />
Apply cleansing milk.<br />
Polish by using<br />
excentric and felt disk<br />
as <strong>for</strong> silky-matt<br />
up to P 400<br />
Platinum pad S 600 15 micron Superpad SG 1200<br />
Platinum pad S 800 9 micron Superpad SG 1500<br />
Platinum pad S 1200 Superpad SG 2000<br />
Hard felt with polishing<br />
paste and lamb's<br />
wool pad<br />
Hard felt with polishing<br />
paste and lamb's<br />
wool pad<br />
Superpad SG 2500<br />
Hard felt with polishing<br />
paste and lamb's<br />
wool pad<br />
For example niche rear wall panelling.<br />
Adhere the <strong>Varicor</strong> ® 3 <strong>mm</strong> panel to the substructure over the whole<br />
surface. In case of wooden substructures, the underside must be<br />
covered with an 0.8 <strong>mm</strong> HPL board as counteracting plate and steam<br />
barrier. Depending on the selection of the carrier material, ask your<br />
adhesive supplier in advance about the appropriate adhesive <strong>for</strong> the<br />
respective underground. After bonding, there must not be any hollow<br />
spaces between <strong>Varicor</strong> ® 3 <strong>mm</strong> and the substructure. Protect the<br />
substructure against penetration of moisture.<br />
An expansion joint must be set horizontally every 800 – 1.000 <strong>mm</strong> <strong>for</strong><br />
wall-high panelling (Fig. 19).<br />
It is possible to join the individual panels at the expansion joints with<br />
tongue and groove, however avoid rigid joints.<br />
Fix the sandwich panel on the wall with suitable profiles (Fig. 20 (*)).<br />
Seal open joints with silicone or polyurethane to prevent penetration<br />
of moisture.<br />
Sources of supply:<br />
(1) Festool, D-Wendlingen (3) HWR Chemie, D-E<strong>mm</strong>ering: Glanz S (+49 8141 5 10 30)<br />
(2) 3M Deutschland, Neuss: Polish paste, type Finesse (4) Jöst GmbH, D-Waldmichelbach<br />
Page 12 of 16