Maestralino Manual Rev5T2_1 - Aria Ventilatori

More documents

Recommendations

Info

IMPORTANT NOTICE ARIA VENTILATORI CEILING FANS REQUIRE PROFESSIONAL INSTALLATION BY A CERTIFIED ELECTRICIAN HOMEOWNERS SHOULD NOT ATTEMPT TO INSTALL THIS PRODUCT ON THEIR OWN Carefully read the installation instructions provided in this manual prior to starting installation. Failure to do so may result in harm to yourself or the ceiling fan. Any damages resulting in failure to follow installation steps as indicated below will result in voiding of all warranties, implied or otherwise. Aria Ventilatori will not accept claims for any damages as a result of improperly installed devices. This fan is not compatible with lighting or speed control systems such as Lutron. It may only be connected through a simple on-off switch.
Step 1: Note for Electrician — INSTALLATION INSTRUCTIONS — Verify by a building contractor and/or structural engineer that the installed framing can support a static load of approximately 40 pounds and moderate vibration for each ceiling fan. The (2) wood lag bolts, 5/16” 3/8” x 4” required to install the fan hanging bracket must be installed directly on a ceiling joist or in a box framed opening to permit proper installation of the fan hanging bracket included in the installation package. When installing on a slope ceiling, make sure to install hanging bracket in same direction as slope. IMPORTANT! The Aria Ventilatori Ceiling Fans cannot be hung from an electrical outlet box. Installer must use the fan hanging bracket provided and attach it directly to structure. Step 2: Install the 4” Electrical Outlet Box 2-1: If fan hanging bracket is to be attached directly to joist, the electrical outlet box must be installed at framing level of joists and not below joists. Failure to do so will make it difficult to properly attach fan hanging bracket subsequently after ceiling finishes have been completed. 2-2: If attaching an electrical outlet box to a timber frame joist or structural beam, it is only required to pre-drill the beam to permit the passage of the electrical lead wire into the ceiling outlet box. Step 3: Prepare the Wiring 3-1: Make sure the circuit breakers to the fan supply line leads and associated wall switch location are turned off. 3-2: Thread the supply line through the outlet box so that the supply line extends to allow splicing to stranded wire going to the fan junction block. If solid wire is connected directly to the fan junction block it will transmit noise. There is very little room in the canopy; the splices and solid wire must fit in the j-box outside the canopy. 3-3: Make certain that the wiring meets all national, state, and local electrical standards and ANSI/NFPA 70. 3-4: The Maestralino Ventilatori is controlled by a remote unit that is included with the installation package. This is a direct wire fan. DO NOT attempt to wire this fan to a fan speed control of any kind. In addition, if an ordinary on-off switch is installed, the fan may be turned on and off with the switch. It will retain in memory the last utilized speed and direction. Verify switch does not have a dimmer installed. Step 4: Installing Ceiling Fan Hanging Bracket 4-1: Verify that the hanging bracket pre-drilled holes align correctly with the support braces or ceiling joists and will attach correctly. Remember that if the ceiling is sloped the hanging bracket must align with the slope to allow the fan to hang vertically. If ceiling material does not exceed 3/4”inch, the hanging bracket may be installed prior to installation of ceiling finish material. After the wiring has been completed and inspected by an electrical inspector, the finish ceiling material may be installed and finished accordingly. The hanging bracket must NOT be installed directly over pliable or compressible ceiling material, such as suspended ceiling tile. 4-2: The cast bronze ceiling fan hanging bracket must be installed directly and centered over the ceiling fan outlet box. Using a pencil, trace the outline of the hanging bracket over the sheetrock, plaster, or wood member indicating the center point of the 2 (two) pre-drilled holes provided in the hanging bracket. Position hanging bracket so that the (2) two pre-drilled holes will align with the direction of the cross support braces if applicable.
Page 1: A R I A V E N T I L AT O R I — TH
Page 5 and 6: Step 6: Verify Fan Motor Rotates Fr
Page 7 and 8: — TROUBLESHOOTING GUIDE — • P

Maestralino Manual Rev5T2_1 - Aria Ventilatori

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?