Hammerfall® DSP System HDSP 9632 - RME

More documents

Recommendations

Info

32.2 Digital Inputs SPDIF (AES/EBU) • 1 x RCA (XLR), transformer-balanced, galvanically isolated, according to AES3-1992 • High-sensitivity input stage (< 0.3 Vpp) • SPDIF compatible (IEC 60958) • Accepts Consumer and Professional format, copy protection will be ignored • Lock Range: 27 kHz – 200 kHz • Jitter when synced to input signal: < 1 ns • Jitter suppression: > 30 dB (2.4 kHz) ADAT Optical • 1 x TOSLINK • Standard: 8 channels 24 bit, up to 48 kHz • Sample Split (S/MUX): 4 channels 24 bit 96 kHz • Bitclock PLL ensures perfect synchronisation even in varispeed operation • Lock Range: 31.5 kHz – 50 kHz • Jitter when synced to input signal: < 1 ns • Jitter suppression: > 30 dB (2.4 kHz) Word Clock • BNC, not terminated (10 kOhm) • Switch for internal termination 75 Ohm • Automatic Double/Quad Speed detection and internal conversion to Single Speed • SteadyClock guarantees super low jitter synchronization even in varispeed operation • Transformer coupled, galvanically isolated input • Not affected by DC-offsets within the network • Signal Adaptation Circuit: signal refresh through auto-center and hysteresis • Overvoltage protection • Level range: 1.0 Vpp – 5.6 Vpp • Lock Range: 27 kHz – 200 kHz • Jitter when synced to input signal: < 1 ns • Jitter suppression: > 30 dB (2.4 kHz) 32.3 Digital Outputs SPDIF • 1 x RCA, transformer-balanced, galvanically isolated, according to AES3-1992 • Output level 0.8 Vpp • Format Professional according to AES3-1992 Amendment 4 • Format Consumer (SPDIF) according to IEC 60958 • Single Wire mode, sample rate 28 kHz up to 200 kHz AES/EBU as SPDIF, but XLR with output voltage 3.5 Vpp ADAT • 1 x TOSLINK • Standard: 8 channels 24 bit, up to 48 kHz • Sample Split (S/MUX): 4 channels 24 bit 96 kHz • In Quad Speed mode output of Single Speed sync frame 76 User's Guide HDSP System HDSP 9632 © RME
Word Clock • 2 x BNC, separated driver stage • Max. output voltage: 5 Vpp • Output voltage @ 75 Ohm termination: 4.0 Vpp • Output impedance: 10 Ohm • Frequency range: 27 kHz – 200 kHz 32.4 Digital • Clocks: Internal, ADAT In, SPDIF In, optional word clock in • Low Jitter Design: < 1 ns in PLL mode, all inputs • Internal clock: 800 ps Jitter, Random Spread Spectrum • Jitter suppression of external clocks: > 30 dB (2.4 kHz) • Effective clock jitter influence on AD and DA conversion: near zero • PLL ensures zero dropout, even at more than 100 ns jitter • Digital Bitclock PLL for trouble-free varispeed ADAT operation • Supported sample rates: 28 kHz up to 200 kHz 32.5 MIDI • 1 x MIDI I/O via 5-pin DIN jacks • Galvanically isolated by optocoupled input • Hi-speed mode: Jitter and response time typically below 1 ms • Separate 128 byte FIFOs for input and output 32.6 Transfer Modes: Resolution / Bits per Sample ASIO • 24 / 32 bit 4 byte (stereo 8 byte) This format is compatible with 16 bit and 20 bit. Resolutions below 24 bit are handled by the audio application. MME • 16 bit 2 byte (stereo 4 bytes) • 16 bit 4 byte MSB (stereo 8 bytes) • 24 bit 4 byte MSB (stereo 8 bytes) • 32 bit 4 byte (stereo 8 bytes) User's Guide HDSP System HDSP 9632 © RME 77
Page 1 and 2:
User's Guide Hammerfall ® DSP Syst
Page 3 and 4:
Driver Installation and Operation -
Page 5 and 6:
User's Guide HDSP 9632 General User
Page 7 and 8:
5. Hardware Installation Before ins
Page 9 and 10:
7. Accessories RME offers several o
Page 11 and 12:
User's Guide HDSP 9632 Driver Insta
Page 13 and 14:
10.4 Firmware Update The Flash Upda
Page 15 and 16:
Pref. Sync Ref. Used to pre-select
Page 17 and 18:
Application examples DDS allows for
Page 19 and 20:
12. Operation and Usage 12.1 Playba
Page 21 and 22:
12.3 Low Latency under MME (Buffer
Page 23 and 24:
12.6 Analog Recording For recording
Page 25 and 26: 15. Using more than one Hammerfall
Page 27 and 28: 17.2 Installation Hammerfall DSP is
Page 29 and 30: 18.2 Channel Routing MME at 96 kHz
Page 31 and 32: User's Guide HDSP 9632 Driver Insta
Page 33 and 34: 20. Configuring the HDSP 9632 20.1
Page 35 and 36: 20.2 Settings dialog - DDS Usually
Page 37 and 38: If several digital devices are to b
Page 39 and 40: 21.3 Supported Sample Rates RME's M
Page 41 and 42: 23. Diagram: Channel Routing at 96
Page 43 and 44: User's Guide HDSP 9632 Connections
Page 45 and 46: 24.2 Line Outputs The short circuit
Page 47 and 48: Note: Recordings with (pre-) emphas
Page 49 and 50: 26.2 Technical Description and Usag
Page 51 and 52: 27. TotalMix: Routing and Monitorin
Page 53 and 54: 27.2 The User Interface The visual
Page 55 and 56: As shown it is very easy to set up
Page 57 and 58: 27.7 The Quick Access Panel This se
Page 59 and 60: 27.9 The Monitor Panel The Monitor
Page 61 and 62: 27.12 Hotkeys In many situations To
Page 63 and 64: 27.14 Level Meter The HDSP 9632 cal
Page 65 and 66: 28.4 Advantages of the Matrix The M
Page 67 and 68: 29.5 Recording a Subgroup (Loopback
Page 69 and 70: Unfortunately, very often it is not
Page 71 and 72: 30.5 Simple MIDI Control The stereo
Page 73 and 74: User's Guide HDSP 9632 Technical Re
Page 75: 32. Technical Specifications 32.1 A
Page 79 and 80: 33.2 Latency and Monitoring The ter
Page 81 and 82: 33.4 QS - Quad Speed Due to the sma
Page 83 and 84: 34. Diagrams 34.1 Block Diagram HDS
Page 85: 34.3 Overview Channels / Expansion
show all

Hammerfall® DSP System HDSP 9632 - RME

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?