Hammerfall® DSP System HDSP 9632 - RME

More documents

Recommendations

Info

17. Hotline – Troubleshooting 17.1 General The newest information can always be found on our website www.rme-audio.com, section FAQ, Latest Additions. The input signal cannot be monitored in real-time • ASIO Direct Monitoring has not been enabled, and/or monitoring has been disabled globally (for example in TotalMix). The 8 ADAT channels don’t seem to work • The optical output has been switched to SPDIF. The ADAT playback devices are still usable by routing and mixing them in TotalMix to other outputs. Playback works, but record doesn’t • Check that there is a valid signal at the input. If so, the current sample frequency is displayed in the Settings dialog. • Check whether the HDSP system has been selected as recording device in the audio application. • Check whether the sample frequency set in the audio application (‘Recording properties’ or similar) matches the input signal. • Check that cables/devices have not been connected in a closed loop. If so, set the systems’s clock mode to Master. Crackle during record or playback • Increase the number and size of buffers in the ‘Settings’ dialog or in the application. • Try different cables (coaxial or optical) to rule out any defects here. • Check that cables/devices have not been connected in a closed loop. If so, set the system’s clock mode to ‘Master’. • Increase the buffer size of the hard disk cache. • Activate Busmaster mode for the hard disks. • In case of a recently done BIOS update of the motherboard: Propably 'Load BIOS Defaults' was loaded instead of 'Load Setup Defaults'. This sets the 'PCI Latency Timer' to 0 (default: 32). Low Latency ASIO operation under Windows 2000/XP on single CPU systems: • To use ASIO at lowest latencies under Windows 2000/XP even when only having one CPU, the system performance has to be optimized for background tasks. Go to >Control Panel/ System/ Advanced/ Performance Options
17.2 Installation Hammerfall DSP is found in the Device Manager (>Settings/ Control Panel/ System
Page 1 and 2: User's Guide Hammerfall ® DSP Syst
Page 3 and 4: Driver Installation and Operation -
Page 5 and 6: User's Guide HDSP 9632 General User
Page 7 and 8: 5. Hardware Installation Before ins
Page 9 and 10: 7. Accessories RME offers several o
Page 11 and 12: User's Guide HDSP 9632 Driver Insta
Page 13 and 14: 10.4 Firmware Update The Flash Upda
Page 15 and 16: Pref. Sync Ref. Used to pre-select
Page 17 and 18: Application examples DDS allows for
Page 19 and 20: 12. Operation and Usage 12.1 Playba
Page 21 and 22: 12.3 Low Latency under MME (Buffer
Page 23 and 24: 12.6 Analog Recording For recording
Page 25: 15. Using more than one Hammerfall
Page 29 and 30: 18.2 Channel Routing MME at 96 kHz
Page 31 and 32: User's Guide HDSP 9632 Driver Insta
Page 33 and 34: 20. Configuring the HDSP 9632 20.1
Page 35 and 36: 20.2 Settings dialog - DDS Usually
Page 37 and 38: If several digital devices are to b
Page 39 and 40: 21.3 Supported Sample Rates RME's M
Page 41 and 42: 23. Diagram: Channel Routing at 96
Page 43 and 44: User's Guide HDSP 9632 Connections
Page 45 and 46: 24.2 Line Outputs The short circuit
Page 47 and 48: Note: Recordings with (pre-) emphas
Page 49 and 50: 26.2 Technical Description and Usag
Page 51 and 52: 27. TotalMix: Routing and Monitorin
Page 53 and 54: 27.2 The User Interface The visual
Page 55 and 56: As shown it is very easy to set up
Page 57 and 58: 27.7 The Quick Access Panel This se
Page 59 and 60: 27.9 The Monitor Panel The Monitor
Page 61 and 62: 27.12 Hotkeys In many situations To
Page 63 and 64: 27.14 Level Meter The HDSP 9632 cal
Page 65 and 66: 28.4 Advantages of the Matrix The M
Page 67 and 68: 29.5 Recording a Subgroup (Loopback
Page 69 and 70: Unfortunately, very often it is not
Page 71 and 72: 30.5 Simple MIDI Control The stereo
Page 73 and 74: User's Guide HDSP 9632 Technical Re
Page 75 and 76: 32. Technical Specifications 32.1 A
Page 77 and 78:
Word Clock • 2 x BNC, separated d
Page 79 and 80:
33.2 Latency and Monitoring The ter
Page 81 and 82:
33.4 QS - Quad Speed Due to the sma
Page 83 and 84:
34. Diagrams 34.1 Block Diagram HDS
Page 85:
34.3 Overview Channels / Expansion
show all

Hammerfall® DSP System HDSP 9632 - RME

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?