Hammerfall® DSP System HDSP 9652 - RME

More documents

Recommendations

Info

Playback works, but record doesn’t • Check that there is a valid signal at the input. If so, the current sample frequency is displayed in the Settings dialog. • Check whether the HDSP system has been selected as recording device in the audio application. • Check whether the sample frequency set in the audio application (‘Recording properties’ or similar) matches the input signal. • Check that cables/devices have not been connected in a closed loop. If so, set the systems’s clock mode to Master. Crackle during record or playback • Increase the number and size of buffers in the ‘Settings’ dialog or in the application. • Try different cables (coaxial or optical) to rule out any defects here. • Check that cables/devices have not been connected in a closed loop. If so, set the system’s clock mode to ‘Master’. • Increase the buffer size of the hard disk cache. • Activate Busmaster mode for the hard disks. • In case of a recently done BIOS update of the motherboard: Propably 'Load BIOS Defaults' was loaded instead of 'Load Setup Defaults'. This sets the 'PCI Latency Timer' to 0 (default: 32). ADAT timecode is running, but Cubase does not start 'Play' automatically • The input displayed in ‘Sync Ref’ is not in sync mode. Sync mode is essential, because ADAT’s so-called time code is really a sample position, and is therefore only valid for synchronous audio data. • Sync is displayed (referring to the card’s clock), but the incoming data is not in sync with the sample position received at the ADAT Sync In. Then Cubase does not start. Remedy: Set ‘Pref. Sync Ref’ to the input corresponding to the received ADAT Sync signal. • Sync mode wasn't activated (button in the transport panel), or ASIO 2.0 has not been chosen as the SMPTE sync source. The ADAT timecode is not in sync • The tape is formatted to 48 kHz, but played back at 44.1 kHz (Pitch). This 'Blackface' problem cannot be solved in a satisfactory way. 17.2 Installation HDSP 9652 is found in the Device Manager (>Settings/ Control Panel/ System
18. Diagrams 18.1 Channel Routing ASIO at 96 kHz This diagram shows the signal paths in ASIO double speed mode (88.2 / 96 kHz). The devices available via the ASIO driver have been designed to avoid conflicts in normal operation. Record and playback are identical. Device: The device name in the audio application SR: Sample Rate Device name code: Channel in ASIO host, interface, HDSP 9652, card number User's Guide HDSP System HDSP 9652 © RME 27
Page 1 and 2: User's Guide Hammerfall ® DSP Syst
Page 3 and 4: Driver Installation and Operation -
Page 5 and 6: User's Guide HDSP 9652 General User
Page 7 and 8: 5. Hardware Installation Before ins
Page 9 and 10: The connectors SYNC1, SYNC2, ST9 an
Page 11 and 12: User's Guide HDSP 9652 Driver Insta
Page 13 and 14: 10.4 Firmware Update The Flash Upda
Page 15 and 16: MME Check Input verifies the curren
Page 17 and 18: To cope with some situations which
Page 19 and 20: 12.2 DVD-Playback (AC-3/DTS) under
Page 21 and 22: 12.5 Digital Recording Unlike analo
Page 23 and 24: 13.3 Synchronization To achieve sam
Page 25: 16. DIGICheck The DIGICheck softwar
Page 29 and 30: User's Guide HDSP 9652 Driver Insta
Page 31 and 32: 20. Configuring the HDSP 9652 20.1
Page 33 and 34: 20.2 Clock Modes - Synchronisation
Page 35 and 36: 21. Mac OS X FAQ 21.1 Round about D
Page 37 and 38: Multicard Operation OS X supports m
Page 39 and 40: User's Guide HDSP 9652 Connections
Page 41 and 42: Note that in record or monitor mode
Page 43 and 44: The HDSP 9652’s word clock input
Page 45 and 46: User's Guide HDSP System HDSP 9652
Page 47 and 48: 26.3 Elements of a Channel A single
Page 49 and 50: You will certainly have noticed tha
Page 51 and 52: Mouse: The original factory presets
Page 53 and 54: Main Monitor Dim: Amount of attenua
Page 55 and 56: 26.13 Menu Options Always on Top: W
Page 57 and 58: 27. TotalMix: The Matrix 27.1 Overv
Page 59 and 60: 28.2 Selection and Group-based Oper
Page 61 and 62: 28.6 Using external Effects Devices
Page 63 and 64: Deactivate MIDI in Background (menu
Page 65 and 66: User's Guide HDSP 9652 Technical Re
Page 67 and 68: 31. Technical Specifications 31.1 D
Page 69 and 70: 32. Technical Background 32.1 Lock
Page 71 and 72: 32.3 DS - Double Speed When activat
Page 73: 33. Block Diagram HDSP 9652 User's

Hammerfall® DSP System HDSP 9652 - RME

Create successful ePaper yourself

Delete template?

Save as template?