download/files/LCQ Deca_Duo Hardware Troubleshooting_8601.pdf

More documents

Recommendations

Info

API-2 API 2 / Off Axis ESI Tangential Movement Probe Geometry ESI probe on a 25 degree slide Ion flow Heated Capillary matrix flow
API-2 API 2 / Off Axis ESI Guidelines LC Flow Rates Infusion or LC at flow rates of 200 µL/min Slide Plate Position Operational Parameters Probe Position (1 to 7) Heated Capillary Temperature Top 4 Typical setting: 250 °C Top 4 Typical setting: 350 °C Top 5 Typical setting: 350 °C Sheath Gas Required Typical setting: 10 to 30 units Required Typical setting: 80+ units Required Typical setting: 80+ units Auxiliary Gas Not required Typical setting: 0 units Required Typical setting: 10 to 20 units Required Typical setting: 10 to 20 units
Page 2 and 3: LCQ Deca/Duo Hardware Troubleshooti
Page 4 and 5: Mass Spectrometer Simplified Schema
Page 6 and 7: Simplified LCQ Schematic Sheath Liq
Page 8 and 9: ESI Ionization Process ESI Ionizati
Page 10 and 11: Aerosol Formation Relative velocity
Page 12 and 13: Cal Mix Tune Parameters API-1 on LC
Page 14 and 15: Troubleshooting the API1 Probe ◗
Page 16 and 17: Sample Tube Elongation ESI Needle S
Page 18 and 19: Divert Valve Configuration TRANSFER
Page 20 and 21: Xcalibur Instrument Setup Divert Va
Page 22 and 23: API-2 / ESI Probe Positions 4 3 2 1
Page 24 and 25: API-2 API 2 / ESI Probe Exploded Pi
Page 26 and 27: LCQ Deca Tune Plus Window LCQ Deca
Page 28 and 29: API-2 API 2 / ESI Probe Assembly Cr
Page 32 and 33: APCI Ionization Process
Page 34 and 35: LCQ Deca / LCQ Duo APCI Probe
Page 36 and 37: LCQ Deca Tune Plus Window LCQ Deca
Page 38 and 39: API-1 API 1 / API-2 API 2 APCI Prob
Page 40 and 41: LCQ API Stack Gas Flow 1 Torr × ×
Page 42 and 43: Cal Mix Tune Parameters LCQ API Sta
Page 44 and 45: Troubleshooting the API Stack ◗ L
Page 46 and 47: Orthogonal Spray Adapter Guidelines
Page 48 and 49: Spiky Noise Characteristics Single
Page 50 and 51: Heated Capillary Cross Section Bent
Page 52 and 53: Octapole 1 Offset: LCQ / LCQ Duo Qu
Page 54 and 55: Cal Mix Tune Parameters LCQ Ion Opt
Page 56 and 57: LCQ Duo Optics Typical Operating Pr
Page 58 and 59: Potential Potential Energy Diagram
Page 60 and 61: RF Tune Diagnostic Dialog RF Tune D
Page 62 and 63: Multipole RF Tune in Calibration Pr
Page 64 and 65: Split Multipole Deca / Duo Configur
Page 66 and 67: -DC LCQ Deca Noise Reduction Split
Page 68 and 69: Mass Selective Instability Simplifi
Page 70 and 71: Quadrupole Ion Trap Operational Par
Page 72 and 73: Troubleshooting the Ion Trap ◗ Lo
Page 74 and 75: Tune RF Modulation LCQ Deca Standin
Page 76 and 77: Affects of Helium on Spectra Helium
Page 78 and 79: 2-Particles enter the multiplier El
Page 80 and 81:
Detection System Parameters ◗ Dyn
Page 82 and 83:
Voltage Life Time of the Electron M
Page 84 and 85:
LCQ Recommended Maintenance Schedul
Page 86 and 87:
LCQ Recommended Maintenance Schedul
Page 88 and 89:
Overview of Diagnostics ◗ Tests a
Page 90 and 91:
Static Results from Status Test +15
Page 92 and 93:
Dynamic Test Dynamic Test Graphical
Page 94 and 95:
Dynamic Results Ion Detection Test
Page 96 and 97:
Power Supplies Power Supplies Stati
Page 98 and 99:
Lenses Static Diagnostic
Page 100 and 101:
RF RF-2 Static Diagnostic
Page 102 and 103:
Toggles/Detector Diagnostic Tool
Page 104 and 105:
Graphs Plotting Conversion Dynode V
Page 106 and 107:
Triggers Research Tool
Page 108 and 109:
Front Panel LEDs Front Panel LEDs D
Page 110 and 111:
LCQ Duo Front Panel LEDs Definition
show all

download/files/LCQ Deca_Duo Hardware Troubleshooting_8601.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?