ESP Panel System brochure and manual - Victron Energy

ESP PANELS TM
& SYSTEM COMPONENTS
Brochure, Instruction and connection manual

Panel range
System monitoring panel
ESP-system
volts
888
domestic start
inverter on
overload
low battery
temperature
on
volts
shore avail
Control panel
ESP-CONTROL
SYSTEM MONITORING
DC MONITORING
charge
discharge
AC MONITORING
MULTI PLUS CONTROL
mains on
bulk
absorp
float
amps
888
battery iso switch
on off
amps
888 888
preheat
shore in use gen in use
shore
current
limiter
off charger only
off on lights
4
8
0
16
12 20
24
30
PANEL CONTROL
page 2 ESP PANELS
28
AC circuit breaker panel
ESP-AC-20A-11
AC SYSTEM CONTROL
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
CONTROL AC SYSTEM CONTROL
start
stop
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
AC circuit breaker panel
ESP-AC-20A-04
DC circuit breaker panel
ESP-DC-20A-11
DC SYSTEM CONTROL
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
DC SYSTEM CONTROL
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
DC circuit breaker panel
ESP-DC-20A-04
ESP VE-Net panel
ESP-VE.NET
VE.NET panel
ESP-VE.NET
VE.NET PANEL
88888
back enter
PHOENIX MULTI CONTROL
inverter on
mains on
8
6 10
overload
boost 4
12
low battery
equalize 2
14
temperature off float
0
16
on charger only shore current limiter
VE.NET BLUE POWER PANEL
SYSTEMS
VE.NET
88888
back enter
ESP Phoenix Multi
Control panel
ESP-MULTI
ESP VE-Net Blue
Power panel
ESP-VE.NET BLUE

Connections to ESP DC Breaker Panel
Fuse 1 OK
Fuse 2 OK
Fuse 3 OK
Fuse 4 OK
Fuse 5 OK
09
Battery
+
connection
Fuse and
supply test
LITTLEFUSE
MEGA
100A
LITTLEFUSE
MEGA
200A
LITTLEFUSE
MEGA
300A
LITTLEFUSE
MEGA
300A
DC Link Box
Main supply OK
Battery connection
reversed if lit
DC Link Box - 5 way
System Panel A
BMV 501/VBC
I+ (c) shunt - bat end
System Panel B
Battery
-
connection
WARNING: Ensure all cables are correctly sized
for the fuse or circuit breaker protecting them.
I- (d) shunt + load end
+VS (e) voltage sense
-VS voltage sense
+ (g) +VE supply
- (f) -VE supply
+ Multi voltage sense
- Multi voltage sense
Mag latch batt. isolator
Mag latch batt. isolator
Negative
returns
E
E
E
E
E
E
E
E
E
E
E
Battery 2 +
20 A
16A
16A
10A
10A
10A
10A
10A
5A
5A
5A
Alternate connection
point for main supply.
Both connections can
be used.
ESP DC Breaker Panel
Negative Busbar (not supplied)
0V from ESP System Panel
(allows System Panel to control backlight)
OR 0V from Boat supply
To 12V or 24V consumer
(Battery +)
Note:
Undo 2 x nuts to remove
backlight PCB to allow
fitting of Custom Window
Label
9V from ESP System Panel
(allows System Panel to control backlight)
OR 9 - 30V from Boat supply
To 12V or 24V consumer
(Battery -)
ESP PANELS page 3

Connections to ESP Breaker Panel - with single AC group
RCD
(not supplied)
WARNING:
The installer must ensure that the rear of the
panel and live bus bar is inaccessible once
installed.
Ensure all cables are correctly sized for the fuse
or circuit breaker protecting them.
page 4 ESP PANELS
20 A
16A
16A
10A
10A
10A
10A
10A
5A
5A
5A
Alternate connection
point for main supply.
Both connections can
be used.
Neutral Busbar (not supplied)
ESP AC Breaker Panel
0V from ESP System Panel
(allows System Panel to control backlight)
OR 0V from Boat supply
To 230V consumer (live)
Note:
Undo 2 x nuts to remove
backlight PCB to allow
fitting of Custom Window
Label
9V from ESP System Panel
(allows System Panel to control backlight)
OR 9 - 30V from Boat supply
To 230V consumer (neutral)
To 230V consumer (earth)
Earth Busbar (not supplied)
All supply & consumer earths to this point

WARNING:
Connections to ESP AC Breaker Panel - with two AC groups
High load
group RCD
(not supplied)
The installer must ensure that the
rear of the panel and live bus bar
is inaccessible once installed.
Ensure all cables are correctly
sized for the fuse or circuit
breaker protecting them.
Inverter group
RCD
(not supplied)
WARNING:
Cut busbar
to separate
high load
and inverter
load groups.
A gap of at
least 5mm is
required.
Inverter group Neutral Busbar
(not supplied)
20 A
16A
16A
10A
10A
10A
10A
10A
5A
5A
5A
ESP AC Breaker Panel
High load group Neutral Busbar
(not supplied)
0V from ESP System Panel
(allows System Panel to control backlight)
OR 0V from Boat supply
To high load 230V consumer (live)
Note:
Undo 2 x nuts to remove
backlight PCB to allow
fitting of Custom Window
Label
To inverter load 230V consumer (live)
9V from ESP System Panel
(allows System Panel to control backlight)
OR 9 - 30V from Boat supply
To high load 230V consumer (neutral)
To inverter load 230V consumer (neutral)
To 230V consumers (earth)
Earth Busbar (not supplied)
All supply & consumer earths to this point
ESP PANELS page 5

Control Panel
9V from ESP System Panel
(allows System Panel to control backlight)
OR 9 - 30V from Boat supply
Note:
A connection PCB is supplied
loose. This allows alternate
switch actions to be fitted prior
to the connection PCB being
soldered onto the switch. Your
distributor can fit the PCB and
switch at time of ordering.
Switch capacity is 4 Amps max.
Switch supplied is centre off
momentary either way.
Alternative switch actions can be
purchased separately
page 6 ESP PANELS
0V from ESP System Panel
(allows System Panel to control backlight)
OR 0V from Boat supply
Note:
Undo 4 x nuts to remove
backlight PCB to allow
fitting of Custom Window
Label

Connections to ESP System Control Panel using Mark 2 DC Link Box
phoenix
Multicompact 12/1200/50
ESP
PowerMan
RJ45
Fuse 1 OK
Fuse 2 OK
Fuse 3 OK
Fuse 4 OK
ESP System Control Panel
Fuse and
supply test
RJ12 RJ12
Fuse 5 OK
LITTLEFUSE
MEGA
300A
09
LITTLEFUSE
MEGA
100A
LITTLEFUSE
MEGA
200A
LITTLEFUSE
MEGA
300A
Main supply OK
RJ45
9V+ for ESP DC & AC Breaker Panel backlight
0V- for ESP DC & AC Breaker Panel backlight
Battery connection
reversed if lit
BMV 501/VBC
Battery
-
connection
DC Link Box
System Panel A
System Panel B
I+ (c) shunt - bat end
I- (d) shunt + load end
+VS (e) voltage sense
-VS voltage sense
+ (g) +VE supply
- (f) -VE supply
+ Multi voltage sense
- Multi voltage sense
Mag latch batt. isolator
Mag latch batt. isolator
Battery 2 +
Negative
ESP returns PANELS page 7
E
E
E
E
E
E
E
E
E
E
E

System Accessories Labelling
ESP PowerMan
The system panel acquires its AC voltage and current from the ESP PowerMan Unit. These provide automatic switching between
shore power, generator and MultiPlus. In addition, high load circuits are disconnected when only Inverter power is available.
ESP PowerMan 20A
Designed for systems with up to 5Kw
generator and one MultiPlus unit.
DC Link Box
The system panel acquires its DC voltage and current from the DC Link Box.
The Link Box provides primary protection for heavy DC consumers and
avoids “spaghetti junction” wiring at the battery terminal.
page 8 ESP PANELS
ESP PowerMan
32A
Designed for
systems with up
to 8Kw generator
and one or two
MultiPlus units.
ESP PowerMan
64A
Designed for
systems with up
to 16Kw generator
and two to four
MultiPlus units
Custom window labels
The Breaker and Control Panels are designed to
accept custom legends, to suit your needs.
Easy to use MS Word templates for these are
available for download at:
www.victronenergy.com
Simply fill these in, print on Laser Film and cut to
size. To install the label, remove the backlight PCB by
undoing the securing nuts. Lay the label onto the rear
of the window and reassemble.

DC Link Box
Starter
Motor
SYSTEM MONITORING
DC MONITORING
volts
amps
charge
888
discharge
battery iso switch
888
domestic start
on off
AC MONITORING
volts
amps
888 888
shore avail shore in use gen in use
MULTI PLUS CONTROL
16
12 20
inverter on
mains on
overload
bulk
8
24
low battery
absorp 4
28
temperature
float
0
30
shore
current
limiter
on
off charger only
off on lights
PANEL CONTROL
A
Alternator
Starter Battery
DC SYSTEM CONTROL
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
SHORE 2
DRUM
CONTROL
MAIN
HYD.
PACK
PORT
CAPSTAN
STBD.
CAPSTAN
SHORE 1
DRUM
CONTROL
Cyrix battery
separator
Fuse 1 OK
Fuse 2 OK
Fuse 3 OK
Fuse 4 OK
Fuse 5 OK
Mag latch
battery
isolator
09
Battery
+
connection
Fuse and
supply test
LITTLEFUSE
MEGA
100A
LITTLEFUSE
MEGA
200A
LITTLEFUSE
MEGA
300A
LITTLEFUSE
MEGA
300A
Main supply OK
Battery connection
reversed if lit
DC Link Box - 5 way
Service Battery
This is not a VE.Net connector
A
C
I+ (c) shunt - bat end
Shunt
Battery
-
connection
BMV-600
Battery Monitor
D B
I- (d) shunt + load end
B
+VS (e) voltage sense
-VS voltage sense
+ (g) +VE supply
- (f) -VE supply
+ Multi voltage sense
- Multi voltage sense
Mag latch batt. isolator
Mag latch batt. isolator
Negative
returns
E
E
E
E
E
E
E
E
E
E
E
Battery 2 +
C
Voltage Sense
connections
phoenix
Multicompact 12/1200/50
A ESP System Panel (available separately)
B BMV-600 connection to DC Link Box via RJ12 cable
C Voltage sense cable for starter battery.
Only required if using System Panel.
D Mag latch contactor for battery isolation (available separately).
Operated by control on System Panel
Only required if using System Panel.
ESP PANELS page 9

System In A Box TM schematic wiring diagrams
SYSTEM IN A BOX with MultiPlus SYSTEM IN A BOX with Multi EasyPlus
Starter
Motor
(not included)
Generator Max 5Kw (option)
ESP PowerMan
- 20A
Low
Loads
Alternator (option)
RCD
BOX
Starter Battery (option)
High
Loads
phoenix
Cyrix battery
separator (option)
Multicompact 12/1200/50
page 10 ESP PANELS
888
SYSTEM MONITORING
DC MONITORING
AC MONITORING
MULTI PLUS CONTROL
888
888 888
Service Battery (option)
AC SYSTEM CONTROL DC SYSTEM CONTROL
DC Link Box
Starter
Motor
(not included)
Generator Max 3.6Kw (option)
ESP PowerMan
- 20A
Alternator (option)
Starter Battery (option)
Cyrix battery
separator (option)
phoenix
EasyaPlus 12/1600/70
888
SYSTEM MONITORING
DC MONITORING
AC MONITORING
888 888
MULTI PLUS CONTROL
888
Service Battery (option)
AC SYSTEM CONTROL DC SYSTEM CONTROL
Low
Loads
High
Loads
DC Link Box

ESP PowerMan 20A connection diagram - MultiPlus
2 core 0.5mm2 or larger
HIGH POWER DISTRIBUTION
LOW POWER DISTRIBUTION
VICTRON BMV-600
(Green terminals)
or
VICTRON VE.Net
BATTERY
CONTROLLER
(Terminals marked NO
relay contacts)
3 core 2.5mm2 or larger
2 core 0.5mm2 or larger
3 core 2.5mm2 or larger
SHORE POWER
3 core 2.5mm2 or larger
2 core 0.5mm2 or larger
VICTRON DUO MULTI
CONTROL PANEL
RJ45 Cat 5 patch lead
3 core 2.5mm2 or larger
3 core 2.5mm2 or larger
3 core 4.0mm2 or larger
RJ45 Cat 5 patch lead
PE N L
230V
AC IN
VICTRON MULTI PLUS
PE N L
230V
AC OUT
GENERATOR Max 5Kw
ESP PANELS page 11

ESP PowerMan 32A connection diagram
2 core 0.5mm2 or larger
SHORE POWER
VICTRON BMV-600
(Green terminals)
or
VICTRON VE.Net
BATTERY
CONTROLLER
(Terminals marked NO
relay contacts)
3 core 6.0mm2 or larger
LOW POWER DISTRIBUTION
HIGH POWER DISTRIBUTION
page 12 ESP PANELS
3 core 6.0mm2 or larger
2 core 0.5mm2 or larger
3 core 6.0mm2 or larger
VICTRON DUO MULTI
CONTROL PANEL
RJ45 Cat 5 patch lead
3 core 6.0mm2 or larger
RJ45 Cat 5 patch lead
PE N L
230V
AC IN
3 core 4.0mm2 or larger
VICTRON MULTI PLUS
PE N L
230V
AC OUT
3 core 4.0mm2 or larger

OPTIONAL SECOND - VICTRON MULTI PLUS
PE N L
230V
AC IN
3 core 4.0mm2 or larger
PE N L
230V
AC OUT
3 core 4.0mm2 or larger
GENERATOR Max 8Kw
Termination detail
ESP PANELS page 13

ESP PowerMan 20A connection diagram - EasyPlus
2 core 0.5mm2 or larger
page 14 ESP PANELS
SHORE POWER
Not
normally
used
3 core 2.5mm2 or larger
2 core 0.5mm2 or larger
VICTRON DUO MULTI
CONTROL PANEL
RJ45 Cat 5 patch lead
3 core 2.5mm2 or larger
3 core 4.0mm2 or larger
RJ45 Cat 5 patch lead
3 core 2.5mm2 or larger
PE N L
230V
AC IN
VICTRON EASY PLUS
PE N L PE N L
230V
230V
AC OUT HIGH AC OUT LOW
3 core 2.5mm2 or larger
3 core 2.5mm2 or larger
GENERATOR Max 5Kw
LOW POWER DISTRIBUTION
HIGH POWER DISTRIBUTION

Product Dimensions
ESP Panels:
Full size panels:
System monitoring panel
ESP-SYSTEM
AC circuit breaker panel
ESP-AC-20A-11
DC circuit breaker panel
ESP-DC-20A-11
All panels:
160mm(W) x 260mm(H)
Half size panels:
ESP VE-Net Blue Power panel
ESP-VE.NET BLUE
VE.Net Panel
ESP-VE.NET
AC circuit breaker panel
ESP-AC-20A-04
DC circuit breaker panel
ESP-DC-20A-04
Control panel
ESP-CONTROL
Blank panel
ESP-BLANK-HALF SIZE
All panels:
160mm(W) x 130mm(H)
Quarter size panels:
ESP VE-Net panel
ESP-VE.NET
ESP Phoenix Multi Control panel
ESP-MULTI
Blank panel
ESP-BLANK- QUARTER SIZE
All panels:
160mm(W) x 65mm(H)
ESP PowerMan:
ESP PowerMan 20A - 250mm(L) x 200mm(W) x 95mm(H)
ESP PowerMan 32A - 380mm(L) x 300mm(W) x 120mm(H)
ESP PowerMan 64A - 460mm(L) x 380mm(W) x 180mm(H)
DC Link Box:
DC Link Box - 380mm(L) x 300mm(W) x 120mm(H)
ESP PANELS page 15

SAL064110020 - (11/07)
ESP PANELS TM
Distributed by:
Victron Energy B.V.
De Paal 35, 1351 JG Almere-Haven
P.O. Box 50016, 1305 AA Almere-Haven
The Netherlands
Tel. +31 (0)36 535 97 00
Fax +31 (0)36 531 16 66 (general + service)
Fax +31 (0)36 535 97 40 (sales)
E-mail sales@victronenergy.com
www.victronenergy.com