W. Richard Bowen and Nidal Hilal 4

REFERENCEs 2
[100] J.E. Sader, J.W.N. Chon, P. Mulvaney, Calibration of rectangular atomic force microscopy
cantilevers, Rev. Sci. Instrum. 70 (10) (1999) 3967–3969.
[101] J. Ralston, I. Larson, M.W. Rutland, A.A. Feiler, M. Kleijn, Atomic force microscopy
and direct surface force measurements (IUPAC technical report), Pure Appl. Chem.
77 (2005) 2149–2170.
[102] L. Hutter, J. Bechhoefer, Calibration of atomic force microscope tips, Rev. Sci.
Instrum. 64 (7) (1993) 1868–1873.
[103] R. Levy, M. Maaloum, Measuring the spring constant of atomic force microscope cantilevers:
thermal fluctuations and other methods, Nanotechnology 13 (2002) 33–37.
[104] H.-J. Butt, M. Jaschke, Calculation of thermal noise in atomic force microscopy,
Nanotechnology 6 (1995) 1–7.
[105] J.L. Hutter, Comment on tilt of atomic force microscope cantilevers: effect on spring
constant and adhesion measurements, Langmuir 21 (2005) 2630–2632.
[106] R.W. Stark, T. Drobek, W.M. Heckl, Thermomechanical noise of a free v shaped cantilever
for atomic force microscopy, Ultramicroscopy 86 (2001) 207–215.
[107] D.A. Walters, J.P. Cleveland, N.H. Thomson, P.K. Hansma, M.A. Wendman,
G. Gurley, V. Elings, Short cantilevers for atomic force microscopy, Rev. Sci. Instrum.
67 (10) (1996) 3583–3590.
[108] A. Torii, M. Sasaki, K. Hane, S. Okuma, A method for determining the spring constant
of cantilevers for atomic force microscopy, Meas. Sci. Technol. 7 (1996) 179–184.
[109] C.T. Gibson, G.S. Watson, S. Myra, Determination of the spring constants of probes
for force microscopy/spectroscopy, Nanotechnology 7 (1996) 259–262.
[110] S.M. Notley, S. Biggs, V.S.J. Craig, Calibration of colloid probe cantilevers using
the dynamic viscous response of a confined liquid, Rev. Sci. Instrum. 74 (9) (2003)
4026–4032.
[111] V.S.J. Craig, C. Neto, In situ calibration of colloid probe cantilevers in force microscopy:
hydrodynamic drag on a sphere approaching a wall, Langmuir 17 (2001)
6018–6022.
[112] N.A. Burnham, X. Chen, C.S. Hodges, G.A. Matei, E.J. Thoreson, C.J. Roberts,
M.C. Davies, S.J.B. Tendler, Comparison of calibration methods for atomic-force
microscopy cantilevers, Nanotechnology 14 (2003) 1–6.
[113] T.J. Senden, W.A. Ducker, Experimental determination of spring constants in atomic
force microscopy, Langmuir 10 (1994) 1003–1004.
[114] J.M. Neumeister, W.A. Ducker, Lateral, normal and longitudinal spring constants of
atomic force microscopy cantilevers, Rev. Sci. Instrum. 65-8 (1994) 2257–2531.
[115] J.E. Sader, Susceptibility of atomic force microscope cantilevers to lateral forces, Rev.
Sci. Instrum. 74 (4) (2003) 2438–2443.
[116] W.A. Ducker, T.J. Senden, R.M. Pashley, Direct measurement of colloidal forces using
an atomic force microscope, Nature 353 (1991) 239–241.
[117] W.A. Ducker, T.J. Senden, Measurement of forces in liquids using a force microscope,
Langmuir 8 (7) (1992) 1831–1836.
[118] M. Götzinger, W. Peukert, Dispersive forces of particle–surface interactions: direct
AFM measurements and modelling, Powder Technol. 130 (2003) 102–103.
[119] X. Li-Chong, B.E. Logan, Interaction forces between colloids and protein-coated surfaces
using an atomic force microscope, Environ. Sci. Technol. 39 (2005) 3592–3600.
[120] G. Gillies, C.A. Prestidge, Colloid probe AFM investigation of the influence of
crosslinking on the interaction behaviour and nano-rheology of colloidal droplets,
Langmuir 21 (2005) 12342–12347.
[121] M. Reitsma, V. Craig, S. Biggs, Elasto-plastic and visco-elastic deformations of a polymer
sphere measured using colloid probe and scanning electron microscopy, Int.
J. Adhesion Adhesives 20 (2000) 445–448.
[122] L.B.R. Castro, M. Kapple, D.F.S. Petri, Adhesion forces between hybrid colloidal particles
and concavilin A, Langmuir 22 (2006) 3757–3762.