V-752EW - Schuss Home Electronic
V-752EW - Schuss Home Electronic V-752EW - Schuss Home Electronic
Disassembly and Reassembly 1-3 The table of clearing, Lubrication and replacement time about principal parts 1) The replacement time of parts is not life of parts. 2) The table 1-1 is that the VCR Set is in normal condition (normal temperature, normal humidity). The checking period may be changed owing to the condition of use, runtime and environmental conditions. 3) Life of the Cylinder Ass’y is depend on the condition of use. 4) See exploded view for location of each parts. D R I V I N G B R A KE * Parts Name T A PE P A T H S Y S T E M S Y S T E M S Y S TE M Checking Period 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 POST TENSION ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ SLANT POST S, T ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ #8 GUIDE SHAFT ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ CAPSTAN SHAFT ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ #9 GUIDE POST ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ #3 GUIDE POST ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ ∆ GUIDE ROLLER S, T ∆ ∆ ∆ O O O O O O O CYLINDER ASS’Y ∆ O O O O O O O O O FE HEAD ∆ ∆ ∆ O O O O O O O ACE HEAD ∆ O O O O O O O O O PINCH ROLLER POST REEL S, T SLEEVE TENSION POST CENTER ∆ O O O O O O O O O LEVER IDLE BOSS (2Point) CAPSTAN MOTOR PULLEY ∆ ∆ ∆ ∆ ∆ O O O O O BELT PULLEY O O O O O O O HOLDER CLUTCH ASS’Y ∆ O O O O O O O O O GEAR CENTER ASS’Y O O O O O O O O O GEAR IDLE (2Point) O O O O O O O O O LOADING MOTOR O O O O O O O O O BAND BRAKE ASS’Y O O O O O O O O O BRAKE T ASS’Y O O O O O O O O O ∆ : Cleaning O : Check and replacement in necessary : Add Oil Remark - To clean the parts, use patch and alcohol (solvent). - After cleaning, use the video tape after alcohol is gone away completely. - We recommend to use oil [EP-50] or solvent. - One or two drops of oil should be applied after cleaning with alcohol. - Periodic time of applying oil (Apply oil after cleaning) - The excessive applying oil may be the cause of malfunction. 4-20 Toshiba
5. Alignment and Adjustment 5-1 Reference 1) X-Point (Tracking center) adjustment, “Head switching adjustment” and “NVRAM option setting” can be adjusted with remote control. 2) When replacing the Micom (IC601) and NVRAM (IC605 ; EEPROM) be sure to adjust the “Head switching adjustment” and “NVRAM option setting”. 3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”. 4) Remote control used for same chassis as a accessory is available for all adjustments. 5) How to adjustment. - Press the “SW713” button on Main PCB to set the adjustment mode. - If the corresponding adjustment button is pressed, the adjustment is performed automatically. - If the adjustment is completed, be sure to turn the power off. 5-1-1 Location of adjustment button of remote control X-Point (Tracking Center) Adjustment NVRAM Option Setting Head Switching Adjustment DISPLAY EJECT 1 2 3 4 5 6 7 8 9 I.SELECT F.ADV MENU REW SLOW SP/LP A.DUB Fig. 5-1 Toshiba 5-1 0 INDEX REC PROG. SAT.MONI. PLAY CURSOR STOP COUNT.RST COUNT/TR AUDIO SAT.CONT. VT-752EW ON/ STANDBY CH TIMER FF TRK CLR/RST PAUSE/STILL OK TV/VIDEO PICTURE
- Seite 1 und 2: SERVICE MANUAL FILE NO. 120-200221
- Seite 3 und 4: 1. Precautions 1. Be sure that all
- Seite 5 und 6: 2. Reference Information 2-1 Operat
- Seite 7 und 8: Decoder anschließen Fernsehgerät
- Seite 9 und 10: Batterien in die Fernbedienung eins
- Seite 11 und 12: Sender manuell einstellen und speic
- Seite 13 und 14: Videokassettentyp wählen Anschlie
- Seite 15 und 16: ShowView-Funktion verwenden (nur V-
- Seite 17 und 18: Videokassette wiedergeben Aufnahme-
- Seite 19 und 20: Kassette in Zeitlupe wiedergeben Au
- Seite 21 und 22: Audio/Video-Cinch-Kabel anschließe
- Seite 23 und 24: Automatisch ausschalten D PROG OPTI
- Seite 25 und 26: 2-2-2 IC501 (LA72646M) Reference In
- Seite 27 und 28: 3. Product Specifications Änderung
- Seite 29 und 30: 4. Disassembly and Reassembly 4-1 C
- Seite 31 und 32: 4-2 Deck Parts Locations 4-2-1 Top
- Seite 33 und 34: 1-1-2 Bottom View ΠGEAR JOINT 1
- Seite 35 und 36: 1-2-3 Slider FL Drive, Gear FL Cam
- Seite 37 und 38: 1-2-7 Motor Loading Ass’y Removal
- Seite 39 und 40: 1-2-11 Lever Pinch Drive, Lever Ten
- Seite 41 und 42: 1-2-15 Disk S, T Reel Removal 1) Li
- Seite 43 und 44: 1-2-19 Lever Unit Pinch Ass’y, Pl
- Seite 45 und 46: 1-2-23 Slider S, T Ass’y Removal
- Seite 47: 1-2-27 Post #8 Guide Ass’y Remova
- Seite 51 und 52: 5-2 Mechanical Adjustment 5-2-1 Tap
- Seite 53 und 54: a. ACE HEAD HEIGHT ADJUSTMENT 1) Ru
- Seite 55 und 56: (3) Check Transitional Operation fr
- Seite 57 und 58: 6. Exploded View 6-1 Packing Assemb
- Seite 59 und 60: 6-2 Instrument Assembly 155 153 101
- Seite 61 und 62: 6-4 Mechanical Parts (Bottom Side)
- Seite 63 und 64: 7. Replacement Parts List Loc.No. T
- Seite 65 und 66: D1SD31 BY430011 0402-001195 DIODE-R
- Seite 67 und 68: C3A17 BY130273 2401-000414 C-AL;10u
- Seite 69 und 70: R1P110 70795683 2007-000290 R-CHIP;
- Seite 71 und 72: R6P03 70795529 2007-000518 R-CHIP;2
- Seite 73: TOSHIBA VIDEO PRODUCTS PTE LTD 438B
5. Alignment and Adjustment<br />
5-1 Reference<br />
1) X-Point (Tracking center) adjustment, “Head switching adjustment” and “NVRAM option setting” can be adjusted with remote control.<br />
2) When replacing the Micom (IC601) and NVRAM (IC605 ; EEPROM) be sure to adjust the “Head switching adjustment” and<br />
“NVRAM option setting”.<br />
3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”.<br />
4) Remote control used for same chassis as a accessory is available for all adjustments.<br />
5) How to adjustment.<br />
- Press the “SW713” button on Main PCB to set the adjustment mode.<br />
- If the corresponding adjustment button is pressed, the adjustment is performed automatically.<br />
- If the adjustment is completed, be sure to turn the power off.<br />
5-1-1 Location of adjustment button of remote control<br />
X-Point (Tracking Center)<br />
Adjustment<br />
NVRAM Option Setting<br />
Head Switching Adjustment<br />
DISPLAY EJECT<br />
1 2 3<br />
4 5 6<br />
7 8 9<br />
I.SELECT<br />
F.ADV<br />
MENU<br />
REW<br />
SLOW<br />
SP/LP<br />
A.DUB<br />
Fig. 5-1<br />
Toshiba 5-1<br />
0<br />
INDEX<br />
REC<br />
PROG.<br />
SAT.MONI.<br />
PLAY<br />
CURSOR<br />
STOP<br />
COUNT.RST<br />
COUNT/TR<br />
AUDIO<br />
SAT.CONT.<br />
VT-<strong>752EW</strong><br />
ON/<br />
STANDBY<br />
CH<br />
TIMER<br />
FF<br />
TRK<br />
CLR/RST<br />
PAUSE/STILL<br />
OK<br />
TV/VIDEO<br />
PICTURE
Change language