Technische Daten / Specifications - Kurth Electronic GmbH
Technische Daten / Specifications - Kurth Electronic GmbH
Technische Daten / Specifications - Kurth Electronic GmbH
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Stand 03/07 - Druckfehler, Irrtümer und technische Änderungen vorbehalten. Alle eingetragenen Warenzeichen und Marken sind, auch wenn nicht ausdrücklich gekennzeichnet, Eigentum der jeweiligen Inhaber.<br />
03/07 Product design and specifications subject to change without notice. All trademarks belong to their respective companies.<br />
Netzwerk - Kabeltester<br />
Network - Cable Tester<br />
KE6000<br />
Der KE6000 von <strong>Kurth</strong> <strong>Electronic</strong> ist ein einfaches<br />
Prüfgerät für Patchkabel, LAN und Fernmeldeverkabelungen.<br />
KE6000 prüft und verifiziert ungeschirmte<br />
und geschirmte Verbindungskabel mit verdrillten<br />
Doppeladern (UTP- und STP-Kabel) in installierten Netzen<br />
oder bei Patchkabeln. Für installierte Netze werden zwei<br />
KE6000 benötigt. Dabei wird dann ein Gerät als Master<br />
und eines als Slave konfiguriert. Der Vorteil ist, dass an<br />
beiden Seiten der Status abgelesen und nach erfolgter<br />
Korrektur der Test von beiden Seiten durchgeführt werden<br />
kann. Dies führt zu einer echten Zeitersparniss. Die<br />
meisten der vorkommenden Fehler wie Vertauschungen,<br />
Unterbrechungen, Kurzschlüsse und Schirmfehler werden<br />
im Display im Klartext angezeigt. Kein umständliches<br />
Mitschreiben von blinkenden und aufleuchtenden LEDs<br />
notwendig. KE6000 liefert eindeutige, schnelle und sofort<br />
auswertbare Statusinformationen im LCD Display.<br />
Der eingebaute und einfach zu aktivierende Signalsender<br />
sendet auf allen Adernpaaren ein Signal welches mit der<br />
optionalen PROBE (Art. Nr. 0.49561) von <strong>Kurth</strong> <strong>Electronic</strong><br />
empfangen werden kann. Damit ist auch schnell ein<br />
<strong>Daten</strong>port oder ein Kabel gefunden.<br />
®<br />
KURTH<br />
ELECTRONIC<br />
LAN - Kabeltester<br />
&einfach<br />
abzulesendes Display<br />
&klare<br />
Darstellung des Kabelstatus<br />
&stoßgeschütztes<br />
Gehäuse<br />
&leicht und kompakt<br />
Prüfung von:<br />
&Durchgang<br />
&Unterbrechung<br />
&Kurzschluss<br />
&Vertauschung<br />
&Schirm<br />
&Mehrfachfehler<br />
Network Tester:<br />
&easy<br />
to read LCD Display<br />
&clear<br />
fault information<br />
&protected<br />
housing<br />
&leightweight<br />
and compact<br />
Checks for:<br />
&continuity<br />
&open<br />
&short<br />
&reversals<br />
&shield<br />
KE6000 is a simple, affordable, fast and efficient Network<br />
cable tester. KE6000 can test UTP and STP patch cables<br />
and by using of two units also installed wiring of Telecom<br />
and Data cables.<br />
KE6000 is simple to use with the large easy to read LCD<br />
display readouts, indicating cable faults or verifying cable<br />
and pin-out-integrity. The fault is shown here as a clear<br />
information - no need for watch and count flashing LEDs. If<br />
KE6000 is used to test a inhouse installation, one unit is set<br />
to Master the other is set to Slave. The big advantage is that<br />
on both sides the LCD display shows the fault. After<br />
corrective action the cable test can be started from both<br />
sides. This saves time and money. KE6000 checks for<br />
Cable faults, including Short Circuit Pairs, Open Circuit<br />
Pairs, Shorts between Pairs, Pair Reversals, Transposed<br />
Pairs and other Cable Miswires are indicated even if there<br />
are multiple faults. A clear wire map is shown in the LCD<br />
Display.<br />
With the build in Tone Transmitter the user is able to send a<br />
trace tone on all pairs to detect the corresponding port or<br />
find an open cable. This is done best with the optional <strong>Kurth</strong><br />
<strong>Electronic</strong> PROBE (Art. No. 0.49561).
Kabeltypen / Cable type<br />
UTP 4paarig, STP, FTP, 568A 568 B, USOC, Coax<br />
<strong>Technische</strong> <strong>Daten</strong> / <strong>Specifications</strong><br />
Fehleranzeige / Fault detection<br />
Kurzschluss, Unterbrechungen, gekreuzte Doppeladern, Vertauschungen, Schirm ja/nein<br />
Short, open, crossed pairs, reversals, shield faults, multiple faults<br />
Kabellänge / cable length<br />
max. 330m / max 1000 ft<br />
Abmessungen / Dimensions<br />
103 x 79 x 27,5 mm ohne Gummischutz /<br />
4 x 3.11 x 1.07 “ without Rubber protection<br />
Standzeit / Battery lifetime<br />
Bis zu 50 Stunden / up to 50 hours<br />
Batterie / Battery<br />
3 x AAA<br />
Temperatur<br />
0 bis 40 °C / 30 to 80 °F<br />
Loop<br />
Back<br />
ON/OFF<br />
Switch<br />
Patch Kabel Test<br />
Patch Cable Test<br />
Master<br />
Display<br />
Mode<br />
switch<br />
0.49400 KE6000 Netzwerk Kabeltester / Network Cabletester<br />
0.49561 Kapazitive Probe / Capacitiv Probe<br />
Anwendung - how to use<br />
Modus<br />
Master<br />
Modus<br />
Slave<br />
Test von Kabel Installationen<br />
Test off installed cable<br />
Bestell Information - Order Informations<br />
Your dealer / Ihr Händler<br />
Modus<br />
Tone<br />
Kabelsuche<br />
Cable tracking<br />
KURTH ELECTRONIC <strong>GmbH</strong> • Im Scherbental 5 • D-72800Eningen u.A. • GERMANY<br />
Tel. +49(0)7121-97 55-0 • Fax +49(0)7121-97 55 56<br />
www.kurthelectronic.de • e-mail: sales@kurthelectronic.de<br />
Probe<br />
KURTH<br />
ELECTRONIC<br />
R<br />
D-72793 Pfullingen Daimlerstrasse 13 GERMANY<br />
Tel. +49 (0)7121-9755-0 Fax +49 (0)9755-56