Montage- und Betriebsanleitung Operation- and Assembly Instruction
Montage- und Betriebsanleitung Operation- and Assembly Instruction
Montage- und Betriebsanleitung Operation- and Assembly Instruction
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
DRIESCHER � WEGBERG<br />
Austausch der HH-Sicherungseinsätze<br />
Verwenden Sie nur HH-Sicherungseinsätze nach<br />
VDE 0670 Teil 4 mit einem Kappendurchmesser bis<br />
maximal 88 mm.<br />
Der Schlagstift der Sicherung muss der Klasse<br />
“mittel” (50N, �20mm) nach VDE 0670 Teil 4<br />
entsprechen.<br />
Auf Gr<strong>und</strong> der Kapselung der Sicherungseinsätze<br />
darf deren Leistungsabgabe 100 W je Phase nicht<br />
überschreiten, bezogen auf den Betriebsstrom bei<br />
40°C.<br />
Ob eine HH-Sicherung angesprochen hat, wird durch<br />
den Schalterstellungsanzeiger in der Sicherungsabdeckblende<br />
durch einen waagerechten Balken<br />
angezeigt.<br />
Nach Ansprechen einer HH-Sicherung sollten stets<br />
alle Sicherungseinsätze ausgetauscht werden, auch<br />
wenn nicht alle geschaltet haben (Vorschädigungen<br />
der Schmelzleiter möglich).<br />
Öffnen der Sicherungsabdeckung<br />
� DRIESCHER � WEGBERG<br />
Die Sicherungsabdeckung lässt sich nur<br />
entfernen, wenn der entsprechende Abzweig<br />
geerdet ist!<br />
- Lösen Sie die Schnellverschlussschrauben mit<br />
der Schaltkurbel (Innensechskant SW14 am roten<br />
Ende).<br />
- Schwenken Sie die Sicherungsblende nach vorne<br />
<strong>und</strong> nehmen diese nach oben weg.<br />
Durch eine Einschaltsperre lässt sich der Erdungs-<br />
<strong>und</strong> Lasttrennschalter bei geöffneter Sicherungsblende<br />
nicht betätigen.<br />
36 MINEX / G.I.S.E.L.A<br />
Replacement of the HV HRC fuses<br />
Only use HV HRC fuses according to IEC 60282-1,<br />
with a cap diameter up to max. 88 mm.<br />
The striker pin of the fuse must be according to the<br />
“medium” class (50 N, � 20 mm) of IEC 60282-1.<br />
Due to the fact that the HV HRC fuses are accommodated<br />
in a fuse tube, the power loss of 100W per<br />
phase may not be exceeded, related to the operating<br />
current value at 40°C.<br />
The operating of a HV HRC fuse is shown by a horizontal<br />
bar at the switch position indicator that is situated<br />
in the fuse cover.<br />
We recommend to replace all fuses, even if not all of<br />
them have operated. (The fuse elements could probably<br />
be damaged).<br />
HH-Sicherung ausgelöst<br />
HV HRC fuse has operated<br />
Normalbetrieb<br />
normal operation<br />
Opening the fuse cover<br />
The fuse cover can only be removed if the<br />
corresponding outgoing circuit is earthed!<br />
- Unscrew the quick release screws with the switch<br />
crank (hexagonal recess SW 14 at the red end).<br />
- Turn the fuse cover forward <strong>and</strong> remove it upwards.<br />
There is a closing lock-out so that the earthing switch<br />
<strong>and</strong> the switch-disconnector cannot be operated with<br />
open fuse cover.