DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber
DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber
EN9.6.2 Filling with the Plastic SyringeNOTICEDo not remove the pump when filling with the plastic syringe.Otherwise, the system is leaky.1. Fill the plastic syringe with the sample.2. Fill the measuring cell through the Luer adapter using the plastic syringe.Fig. 9 - 2Filling sample using the plastic syringe48 C96IB01
9.7 Performing a MeasurementEN1. Select the measuring unit (see Chapter 9.1) or measuring method (see Chapter9.2).2. Define a sample ID if you want to assign the measurement results to a specificsample (see Chapter 9.3).3. Fill the measuring cell with the sample.4. Press the key on the back of DMA 35.The measured value is displayed as soon as the result has stabilized. Themeasured value with all corresponding data is now saved in the results list.5. Press to return to the measuring mode.9.7.1 Deleting the Measured Value• Press instead of when the measured value appears on thedisplay.The measured value is deleted and the instrument returns to the measuringmode.9.7.2 Printing the Measured ValueYou can transfer the measured value to a printer via the IrDA interface. For acompatible printer, contact your Anton Paar representative.1. Allocate the softkey the command (see Chapter 8.7).2. Switch on the printer with the IrDA interface.3. Press the key when the measured value appears on the display.4. Hold the IrDA interface of DMA 35 to the IrDA interface of the printer to establishcommunication between the printer and density meter.The measured value is printed.You can also print out all or only the last measuring data (see Chapter 9.10).9.7.3 Emptying the Measuring Cell1. Place the filling tube in a vessel which is suitable for sample disposal.2. Empty the measuring cell by pressing the pump lever.C96IB01 49
- Seite 1: DMA 35Portable Density/Specific Gra
- Seite 4 und 5: ENWhile every precaution has been t
- Seite 6 und 7: EN9.1.3 Importing Custom Functions
- Seite 8 und 9: EN1 About the Instruction ManualThi
- Seite 10 und 11: EN2 Safety Instructions• Read thi
- Seite 12 und 13: EN• Do not leave sample/rinsing c
- Seite 14 und 15: EN5 Checking the Supplied PartsDMA
- Seite 16 und 17: ENTable 5.2: Optional partsArticle
- Seite 18 und 19: EN2 314Fig. 6 - 2 Top view of DMA 3
- Seite 20 und 21: EN6.3 Display23b3a1412561171098Fig.
- Seite 22 und 23: EN7 Operating the DMA 357.1 Connect
- Seite 24 und 25: EN8 Defining the Basic Settings8.1
- Seite 26 und 27: EN8.7 Allocation of the Softkey Fun
- Seite 28 und 29: ENTo set the time format1. Press a
- Seite 30 und 31: EN• Make sure to carefully clean
- Seite 32 und 33: ENMeas. OptionsDescriptionunitsBaum
- Seite 34 und 35: EN9.2 Selecting Measuring MethodsAp
- Seite 36 und 37: ENMethod list templateThe following
- Seite 38 und 39: EN9.2.6 Selecting a Method1. Press
- Seite 40 und 41: ENSample ID listThe following table
- Seite 42 und 43: EN9.4 Selecting the Measurement Mod
- Seite 44 und 45: EN9.5.3 Programming RFID TagsBeside
- Seite 46 und 47: EN3. Hold the allocated or programm
- Seite 50 und 51: EN9.8 Accessing Saved Measuring Dat
- Seite 52 und 53: EN5. Select to export the whole li
- Seite 54 und 55: EN10 Cleaning and Storing the Instr
- Seite 56 und 57: EN11 Maintenance11.1 Changing the B
- Seite 58 und 59: ENFig. 11 - 3Removing the pump lock
- Seite 60 und 61: EN11.3.1 Accessing Device Informati
- Seite 62 und 63: EN12 ReadjustmentTo ensure accurate
- Seite 64 und 65: EN12.5 Restoring to Factory Adjustm
- Seite 66 und 67: EN14 Technical DataMeasuring range:
- Seite 68 und 69: ENAppendix A: Density of Water 4 (0
- Seite 70 und 71: ENID Measuring unit Minimum Maximum
- Seite 72 und 73: ENAppendix C: CE Declarations of Co
- Seite 74 und 75: ENAppendix D: EC-Type-Examination C
- Seite 76 und 77: ENAppendix E: RFID Module Test Repo
- Seite 78 und 79: ENAppendix F: Firmware VersionsFirm
- Seite 80 und 81: ENSetup Measurement Mode Precise; F
- Seite 82 und 83: DEDieses Dokument wurde mit der nö
- Seite 84 und 85: DE9.1.3 Kundenfunktionen importiere
- Seite 86 und 87: DE1 Zur BetriebsanleitungDiese Betr
- Seite 88 und 89: DE2 Sicherheitshinweise• Lesen Si
- Seite 90 und 91: DESchutzmaßnahmen bei leicht entz
- Seite 92 und 93: DE4 DMA 35 - ein ÜberblickDas DMA
- Seite 94 und 95: DETabelle 5.1: Gelieferte TeileSymb
- Seite 96 und 97: DE6 Beschreibung des Gerätes6.1 Vo
9.7 Performing a MeasurementEN1. Select the measuring unit (see Chapter 9.1) or measuring method (see Chapter9.2).2. Define a sample ID if you want to assign the measurement results to a specificsample (see Chapter 9.3).3. Fill the measuring cell with the sample.4. Press the key on the back of <strong>DMA</strong> <strong>35</strong>.The measured value is displayed as soon as the result has stabilized. Themeasured value with all corresponding data is now saved in the results list.5. Press to return to the measuring mode.9.7.1 Deleting the Measured Value• Press instead of when the measured value appears on thedisplay.The measured value is deleted and the instrument returns to the measuringmode.9.7.2 Printing the Measured ValueYou can transfer the measured value to a printer via the IrDA interface. For acompatible printer, contact your Anton Paar representative.1. Allocate the softkey the command (see Chapter 8.7).2. Switch on the printer with the IrDA interface.3. Press the key when the measured value appears on the display.4. Hold the IrDA interface of <strong>DMA</strong> <strong>35</strong> to the IrDA interface of the printer to establishcommunication between the printer and density meter.The measured value is printed.You can also print out all or only the last measuring data (see Chapter 9.10).9.7.3 Emptying the Measuring Cell1. Place the filling tube in a vessel which is suitable for sample disposal.2. Empty the measuring cell by pressing the pump lever.C96IB01 49