DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber
DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber DMA 35 Portable Density/Specific Gravity/ Concentration Meter - Alber
EN3. Hold the allocated or programmed RFID tag to the RFID interface of theinstrument.The method and/or sample ID allocated to or stored on the RFID tag willautomatically be used for the following measurements.9.5.7 Application Examples for RFIDRFID tags can be attached on the outside of tank farms, for example. Before anemployee takes a sample from the tank to measure it, the measuring method andsample ID to be used can be changed accordingly by reading the RFID tag.The RFID function also proves to be useful when inspecting incoming goods: Foreach incoming good you can allocate an RFID tag to the measuring method andsample ID to be used and catalog the tags. By doing this, the allocated RFID tag caneasily be scanned from the catalog when the substance is coming in, a sample canbe taken and measured and traced back via the sample ID later.46 C96IB01
9.6 Filling SampleENDepending on the viscosity of the sample, you can fill the measuring cell using thefilling tube or the plastic syringe. When filling highly viscous samples, we recommendusing the plastic syringe.9.6.1 Filling Using the Filling Tube1. Press down the pump lever as far as it will go (see Fig. 9 - 1).2. Submerge the filling tube in the sample.3. Slowly release the pump lever.Fig. 9 - 1Filling sample using the filling tubeC96IB01 47
- Seite 1: DMA 35Portable Density/Specific Gra
- Seite 4 und 5: ENWhile every precaution has been t
- Seite 6 und 7: EN9.1.3 Importing Custom Functions
- Seite 8 und 9: EN1 About the Instruction ManualThi
- Seite 10 und 11: EN2 Safety Instructions• Read thi
- Seite 12 und 13: EN• Do not leave sample/rinsing c
- Seite 14 und 15: EN5 Checking the Supplied PartsDMA
- Seite 16 und 17: ENTable 5.2: Optional partsArticle
- Seite 18 und 19: EN2 314Fig. 6 - 2 Top view of DMA 3
- Seite 20 und 21: EN6.3 Display23b3a1412561171098Fig.
- Seite 22 und 23: EN7 Operating the DMA 357.1 Connect
- Seite 24 und 25: EN8 Defining the Basic Settings8.1
- Seite 26 und 27: EN8.7 Allocation of the Softkey Fun
- Seite 28 und 29: ENTo set the time format1. Press a
- Seite 30 und 31: EN• Make sure to carefully clean
- Seite 32 und 33: ENMeas. OptionsDescriptionunitsBaum
- Seite 34 und 35: EN9.2 Selecting Measuring MethodsAp
- Seite 36 und 37: ENMethod list templateThe following
- Seite 38 und 39: EN9.2.6 Selecting a Method1. Press
- Seite 40 und 41: ENSample ID listThe following table
- Seite 42 und 43: EN9.4 Selecting the Measurement Mod
- Seite 44 und 45: EN9.5.3 Programming RFID TagsBeside
- Seite 48 und 49: EN9.6.2 Filling with the Plastic Sy
- Seite 50 und 51: EN9.8 Accessing Saved Measuring Dat
- Seite 52 und 53: EN5. Select to export the whole li
- Seite 54 und 55: EN10 Cleaning and Storing the Instr
- Seite 56 und 57: EN11 Maintenance11.1 Changing the B
- Seite 58 und 59: ENFig. 11 - 3Removing the pump lock
- Seite 60 und 61: EN11.3.1 Accessing Device Informati
- Seite 62 und 63: EN12 ReadjustmentTo ensure accurate
- Seite 64 und 65: EN12.5 Restoring to Factory Adjustm
- Seite 66 und 67: EN14 Technical DataMeasuring range:
- Seite 68 und 69: ENAppendix A: Density of Water 4 (0
- Seite 70 und 71: ENID Measuring unit Minimum Maximum
- Seite 72 und 73: ENAppendix C: CE Declarations of Co
- Seite 74 und 75: ENAppendix D: EC-Type-Examination C
- Seite 76 und 77: ENAppendix E: RFID Module Test Repo
- Seite 78 und 79: ENAppendix F: Firmware VersionsFirm
- Seite 80 und 81: ENSetup Measurement Mode Precise; F
- Seite 82 und 83: DEDieses Dokument wurde mit der nö
- Seite 84 und 85: DE9.1.3 Kundenfunktionen importiere
- Seite 86 und 87: DE1 Zur BetriebsanleitungDiese Betr
- Seite 88 und 89: DE2 Sicherheitshinweise• Lesen Si
- Seite 90 und 91: DESchutzmaßnahmen bei leicht entz
- Seite 92 und 93: DE4 DMA 35 - ein ÜberblickDas DMA
- Seite 94 und 95: DETabelle 5.1: Gelieferte TeileSymb
9.6 Filling SampleENDepending on the viscosity of the sample, you can fill the measuring cell using thefilling tube or the plastic syringe. When filling highly viscous samples, we recommendusing the plastic syringe.9.6.1 Filling Using the Filling Tube1. Press down the pump lever as far as it will go (see Fig. 9 - 1).2. Submerge the filling tube in the sample.3. Slowly release the pump lever.Fig. 9 - 1Filling sample using the filling tubeC96IB01 47