Technical information and operating instruction ... - STG-Beikirch
Technical information and operating instruction ... - STG-Beikirch
Technical information and operating instruction ... - STG-Beikirch
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
8<br />
Funktionsstörung<br />
Fehlerbeh<strong>and</strong>lung und Weiterleitung<br />
Fehler, die im MZ2 System erscheinen werden an das LON Netz<br />
weitergeleitet, wenn RWA- oder Meldergruppen verknüpft sind.<br />
Lüftungs-, Wind/Regen- und Temperatur-Verknüpfungen senden<br />
keine Fehler an das LON Netz. Akku und 230 V Netz Fehler werden<br />
an alle Linen im LON Netz gesendet.<br />
Blinkcode Tabelle<br />
Erkannte Fehler werden als Blinkfolge über die gelben Störungs-<br />
LED‘s ausgegeben. L = Wird der Blinkcode durch ein langes Blink-<br />
signal eingeleitet, so stammt der Fehler von einem <strong>and</strong>eren Modul.<br />
Die Blinkfolgen haben folgende Bedeutung:<br />
Blinkfolge<br />
Flash Code<br />
DAUER<br />
DURATION<br />
1<br />
6<br />
8<br />
10<br />
11<br />
12<br />
L+2<br />
L+6<br />
AUS<br />
OFF<br />
Fehler<br />
Error<br />
Initdaten<br />
Initdata<br />
Netzfehler<br />
Mains failureInitdata<br />
Busfehler<br />
Bus error<br />
Selbsttest<br />
Self test<br />
Versorgung +5 V<br />
Supply +5 V<br />
Versorgung +24 V<br />
Supply +24 V<br />
Melder Kurzschluss<br />
Short-circuit of detector<br />
Netzmodulfehler (NM)<br />
Error of the power pack (NM)<br />
LON Fehler<br />
Error of LON<br />
kein Fehler<br />
no error<br />
Auslöser<br />
Cause of Error<br />
Failure malfunction<br />
Error h<strong>and</strong>ling <strong>and</strong> transmission<br />
Errors which occur in the MZ2 system are transmitted to the LON<br />
network if SHE or alarm groups are linked. Ventilation, wind/rain<br />
<strong>and</strong> temperature links send no errors to the LON network. Battery<br />
<strong>and</strong> 230 V mains errors are sent to all lines in the LON network.<br />
Flashing code chart<br />
Errors recognised are emitted as a flashing sequence via the yellow<br />
LEDs fault. L = If the flashing codes is introduced by a long<br />
flashing signal, then the fault originates from another module.<br />
The flashing codes have the following meanings:<br />
Initialisierungsdaten fehlen oder Prozessor läuft nicht<br />
Initialisation data missimg or processor not running<br />
Netzspannung fehlt (Notbetrieb)<br />
Mains voltage missing (emergency operation)<br />
Kommunikation mit der CPU gestört<br />
Communication with the CPU disrupted<br />
Programmüberwachung<br />
Program monitoring<br />
int. Versorgungsspannung +5 V fehlerhaft<br />
int. supply voltage +5 V faulty<br />
int. Versorgungsspannung +24 V fehlerhaft<br />
int. supply voltage +24 V faulty<br />
Kurzschluss im Melderkreis<br />
Short-circuit of detector circuit<br />
Fehler im Netzmodul<br />
Error of the power pack<br />
Ein Knoten aus dem LON Netz hat einen Fehler übermittelt<br />
Ein Knoten aus dem LON Netz hat einen Fehler übermittelt<br />
---