Finish 270 Finish 250 - Wagner
Finish 270 Finish 250 - Wagner Finish 270 Finish 250 - Wagner
GBFinish 270 / 250Cleaning the unit / Servicing9 Servicing9.1 General servicingAn annual expert check is higly recomendedto be sure to have an safe unit8.4 Cleaning the Airless spray gun1. Rinse the Airless spray gun with a suitable cleaning agentunder lower operating pressure.2. Clean the tip thoroughly with a suitable cleaning agent sothat no suitable coating material rests remain.3. Do not store the tip in solvent because this reduces thedurability considerably.4. Clean the outside of the Airless spray gun thoroughly.You can servicing of the unit carried out bythe Wagner Service. Favorable conditions canbe agreed with a service agreement and/ormaintenance packages.Minimum check before every startup:1. Check the high-pressure hose, spray gun with rotary joint,power supply cable with plug for damage.2. Check whether the pressure gage can be read.check at periodical intervals:1. Check inlet-, outlet-, relief valve according wear. Clean itand replace worn out parts.2. Check all filter inserts (spray gun, suction system) clean itand replace if necessary.1329.2 High-pressure hoseInspect the high-pressure hose visually for any notches orbulges, in particular at the transition in the fittings. It must bepossible to turn the union nuts freely. A conductivity of lessthan1 MΩ must exist across the entire length.Have all the electric tests carried by the WagnerService.Insertion filter in the Airless spray gunRemoval1. Pull the protective bracket (1) forwards.2. Screw the grip (2) out of the gun housing. Pull out the insertionfilter (3).3. If the insertion filter is clogged or defective, replace it.Installation1. Slide the insertion filter (3) with the longer cone into thegun housing.2. Screw the grip (2) into the gun housing and tighten it.3. Latch in the protective bracket (1).44
Finish 270 / 250GBRepairs at the unit10 Repairs at the unitSwitch the unit off.Before all repair work: Unplug the powerplug from the outlet.10.1 Inlet valve Pusher1. Use a 17 mm spanner to screw out the inlet valve button.2. Replace the wiper (1) and O-ring (2).Installation1. Insert the inlet valve (2) into the trigger housing (1) andsecure with the clasp (3). Ensure that the (black) seal (5) ismounted in the trigger housing.2. Screw the unit from the trigger housing and the inlet valveinto the paint section. The same (black) seal (6) has tobe mounted in the paint section.3. Tighten the trigger housing with the 30 mm wrench andtighten with three light blows of the hammer on the endof the wrench. (Corresponds to approx. 90 Nm tighteningtorque).2131524610.2 Inlet valve1. Place the enclosed 30 mm wrench on the trigger housing(1).2. Loosen the trigger housing (1) with light blows of a hammeron the end of the wrench.3. Screw out the trigger housing with the inlet valve (2) fromthe paint section.4. Pull of the clasp (3) using the enclosed screwdriver.5. Place the enclosed 30 mm wrench on the inlet valve (2).Turn out the inlet valve carefully.6. Clean the valve seat (4) with a cleaning agent and brush(ensure that no brush hairs are left behind).7. Clean the seals (5, 6) and check for damage. Replace, if necessary.8. Check all the valve parts for damage. In case of visiblewear replace the inlet valve.10.3 Outlet valve1. Use a 22 mm wrench to screw the outlet valve from thepaint section.2. Carefully pull of the clasp (1) using the enclosed screwdriver.The compression spring (2) presses ball (4) and valveseat (5) out.3. Clean or replace the components.4. Check the O-ring (7) for damage.5. Check the installation position when mounting the springsupport ring (3) (clipped onto spring (2)), outlet valve seat(5) and seal (6), refer to figure.45
- Seite 3 und 4: Finish 270 / 250dDInhaltsverzeichni
- Seite 5 und 6: Finish 270 / 250dSicherheitsvorschr
- Seite 7 und 8: Finish 270 / 250dGerätebeschreibun
- Seite 9 und 10: Finish 270 / 250dGerätebeschreibun
- Seite 11 und 12: Finish 270 / 250dInbetriebnahme4.5
- Seite 13 und 14: Finish 270 / 250dgerätereinigung8
- Seite 15 und 16: Finish 270 / 250dgeräteReinigung /
- Seite 17 und 18: Finish 270 / 250dreparaturen am ger
- Seite 19 und 20: Finish 270 / 250dreparaturen am ger
- Seite 21 und 22: Finish 270 / 250dErsatzteile und Zu
- Seite 23: Finish 270 / 250dersatzteile und zu
- Seite 26 und 27: dFinish 270 / 250ersatzteile und zu
- Seite 28 und 29: dFinish 270 / 250Servicenetz in Deu
- Seite 30 und 31: dFinish 270 / 250Garantieerklärung
- Seite 32 und 33: GBFinish 270 / 250ContentsContents1
- Seite 34 und 35: GBFinish 270 / 250Safety regulation
- Seite 36 und 37: GBFinish 270 / 250General view of a
- Seite 38 und 39: GBFinish 270 / 250Description of un
- Seite 40 und 41: GBFinish 270 / 250Startup4.5 Cleani
- Seite 42 und 43: GBFinish 270 / 250Displays at the u
- Seite 46 und 47: GBFinish 270 / 250Repairs at the un
- Seite 48 und 49: GBFinish 270 / 250Repairs at the un
- Seite 50 und 51: GBFinish 270 / 250Spare parts and a
- Seite 52 und 53: GBFinish 270 / 250Spare parts and a
- Seite 54 und 55: GBFinish 270 / 250Spare parts and a
- Seite 56 und 57: GBFinish 270 / 250Spare parts and a
- Seite 58 und 59: GBFinish 270 / 250notesclaims must
- Seite 60 und 61: FFinish 270 / 250Table des matière
- Seite 62 und 63: FFinish 270 / 250Prescriptions de s
- Seite 64 und 65: FFinish 270 / 250Description de l'a
- Seite 66 und 67: FFinish 270 / 250Description de l'a
- Seite 68 und 69: FFinish 270 / 250Mise en service4.5
- Seite 70 und 71: FFinish 270 / 250Nettoyage de l'app
- Seite 72 und 73: FFinish 270 / 250Maintenance3. Dév
- Seite 74 und 75: FFinish 270 / 250Réparations sur l
- Seite 76 und 77: FFinish 270 / 250Réparations sur l
- Seite 78 und 79: FFinish 270 / 250Réparations sur l
- Seite 80 und 81: FFinish 270 / 250pièces de rechang
- Seite 82 und 83: FFinish 270 / 250pièces de rechang
- Seite 84 und 85: FFinish 270 / 250pièces de rechang
- Seite 86 und 87: FFinish 270 / 250pièces de rechang
- Seite 88 und 89: FFinish 270 / 250Déclaration de ga
- Seite 90 und 91: NLFinish 270 / 250InhoudsopgaveInho
- Seite 92 und 93: NLFinish 270 / 250Veiligheidsvoorsc
GB<strong>Finish</strong> <strong>270</strong> / <strong>250</strong>Cleaning the unit / Servicing9 Servicing9.1 General servicingAn annual expert check is higly recomendedto be sure to have an safe unit8.4 Cleaning the Airless spray gun1. Rinse the Airless spray gun with a suitable cleaning agentunder lower operating pressure.2. Clean the tip thoroughly with a suitable cleaning agent sothat no suitable coating material rests remain.3. Do not store the tip in solvent because this reduces thedurability considerably.4. Clean the outside of the Airless spray gun thoroughly.You can servicing of the unit carried out bythe <strong>Wagner</strong> Service. Favorable conditions canbe agreed with a service agreement and/ormaintenance packages.Minimum check before every startup:1. Check the high-pressure hose, spray gun with rotary joint,power supply cable with plug for damage.2. Check whether the pressure gage can be read.check at periodical intervals:1. Check inlet-, outlet-, relief valve according wear. Clean itand replace worn out parts.2. Check all filter inserts (spray gun, suction system) clean itand replace if necessary.1329.2 High-pressure hoseInspect the high-pressure hose visually for any notches orbulges, in particular at the transition in the fittings. It must bepossible to turn the union nuts freely. A conductivity of lessthan1 MΩ must exist across the entire length.Have all the electric tests carried by the <strong>Wagner</strong>Service.Insertion filter in the Airless spray gunRemoval1. Pull the protective bracket (1) forwards.2. Screw the grip (2) out of the gun housing. Pull out the insertionfilter (3).3. If the insertion filter is clogged or defective, replace it.Installation1. Slide the insertion filter (3) with the longer cone into thegun housing.2. Screw the grip (2) into the gun housing and tighten it.3. Latch in the protective bracket (1).44