PDF-Prospektblatt - Esska Maschinen Vertriebs GmbH

Weitere Magazine

Empfehlungen

Info

MatCut 700 ESSKA Maschinen ESSKA Vertriebs GmbH Web: http://www.esska.de Mail: info@esska.de Exploded drawing E- 1 Eccenter cover E- 8 Eccenter Wire 5-core, 3LNPE E- 2 Eccenter bolt E- 9 Eccenter housing 1x Ground E- 3 Eccenter clamp E-10 Bolt screw 1x Neutral E- 4 C-Clip (2 required) E-11 Knife bolt 3x Phase E- 5 Bearing seal (2 required) ME-80L Knife (left) E- 6 C-Clip (2 required) ME-80R Knife (right) E- 7 Bearing (2 required) ESSKA Maschinen Vertriebs GmbH * Wöhlerstrasse 8 * D-22113 Hamburg * Tel. +49-(0)40-731 036-0 * Fax +49-(0)40-731 036 50 KF Technik Handel GmbH * Am Fischereihafen 101 * D-18069 Rostock * Tel. +49-(0)381-800 58 24 * Fax +49-(0)381-800 58 26 Sweden ESSKA Industriteknik * Karlstadsvägen 2 * S-67142 Arvika * Tel. +46-(0)570-711 622 * Fax +46-(0)570-711 622
MatCut 700 ESSKA Maschinen ESSKA Vertriebs GmbH Web: http://www.esska.de Mail: info@esska.de Instructions MATCUT 700 is a device for slitting glassfibre rolls in widths commonly used in composite production. MATCUT 700 is designed to quickly cut rolls of various widths. Follow these operation and marntenance instructions to insure safe and efficient operation of this machine. The regulations of this manual apply only if the machine is properly being used. Failure tocorrectly adhere to these instruction will void any an all warranties. 1. Operation For good cutting results, the machine must stand on level ground. Have a professional electrician connecting the machine. Have a licenced, professional electrician connect the machine. Be sure polarity is correct an the machine is rotating in the correct direction as indicated on the blade cam over. Be sure the gas-pressure-spring between motor and machine is properly fixed . Before beginning operation, remove the protection over the blades. Attention, they are extremely sharp! Be sure the knives can be moved freely by inserting the proper hex key into the screw E-2, then turning the motor by hand. It must possible to easily move the knives without much force. Rotate the motor by hand at least five times around. Replace blade cam cover and start motor again. Immediately press the red stop button. The stop button is released by making a 1/8 in the direction of the marked arrow. Important: to achieve this, lift hoop slightly. Repeat this procedure, now stopping the motor in the down position, allowing the hoop to come in contact with the sensor. The sensor will interrupt power to the motor. Note: the motor will not start unless the hoop is raised and contact is broken between the sensor and the hoop. 2. Cutting the glassfibre rolls Lift the hope until the gas-pressure-spring stops it's upward motion, allowing the protective blade guard to snap into place. Place the glassfibre roll onto the tub and set your desired measuring from the right edge of the knives. Now unlock the protection device, start the motor an put the machine into operation. Press the sawing hoop moderately down allowing the knives to cut at their own speed. Take hold of the second arm in order to lead the hoop further down. As soon as you come near the cardboard core, reduce the pressure, allowing the knives to continue to cut through the core properly. When you pass trough the core, the cutting process continues with an accelerated speed. Be sure to lighten your pressure just before you complete your pass through the roll, not to rip the final section. 3. Lifting out the slit rolls Leave the sawing hoop down and remove the slit roll. By leaving the blades in the down position, you insure unintentional contact with the blade. 4. Precision cutting device option The precision cutting device consists of the left and the right material stop. These stops move on a ground steel shaft and may be swung out of the way if necessary. To cut small, precise slits, fix the roll tightly between both stops. This will stabilize the roll for more accurate slitting. The precision of the cut depends on various factors: Blade sharpnedd; Consistency of material; Tightness of roll; Operator skill and consistency. ESSKA Maschinen Vertriebs GmbH * Wöhlerstrasse 8 * D-22113 Hamburg * Tel. +49-(0)40-731 036-0 * Fax +49-(0)40-731 036 50 KF Technik Handel GmbH * Am Fischereihafen 101 * D-18069 Rostock * Tel. +49-(0)381-800 58 24 * Fax +49-(0)381-800 58 26 Sweden ESSKA Industriteknik * Karlstadsvägen 2 * S-67142 Arvika * Tel. +46-(0)570-711 622 * Fax +46-(0)570-711 622
Seite 1 und 2: MatCut 700 ESSKA Maschinen ESSKA Ve
Seite 3: MatCut 700 ESSKA Maschinen ESSKA Ve

PDF-Prospektblatt - Esska Maschinen Vertriebs GmbH

Erfolgreiche ePaper selbst erstellen

Template löschen?

Als Template speichern?