Rasenmäher JX90CB BETRIEBSANLEITUNG Tondeuse à gazon ...
Rasenmäher JX90CB BETRIEBSANLEITUNG Tondeuse à gazon ...
Rasenmäher JX90CB BETRIEBSANLEITUNG Tondeuse à gazon ...
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
GB<br />
Pos:<br />
17. 3.6 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Mä her fäh rt nic ht @ 0\m od_ 111 537 6736 218 _15 21.d oc @ 188 9<br />
Mower will not move forward<br />
Pos: 17. 3.7 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Fa hr geschwi ndigk eit kan n nic ht r egulie rt we rde n @ 0\m od_1 127 909 363 598 _15 21.d oc @ 188 8<br />
Drive speed cannot be<br />
regulated<br />
Switch-on lever of cutting unit not<br />
actuated<br />
Did not observe the sequence for<br />
switching the mower on.<br />
Too much grass residue underneath<br />
the housing<br />
Swiftly push the lever forward up to the stop<br />
and release H3 .<br />
Switch holder and switch-on lever of the<br />
mower must be actuated in the specified<br />
sequence.<br />
Remove grass from cutting space.<br />
Keep gap between fan and housing clean.<br />
Check cutting blade for freedom of motion.<br />
Attention! Please observe safety<br />
information before starting these activities.<br />
Get it checked by an authorized workshop.<br />
Drive control bracket not pulled. Pull drive switch bar G .<br />
Have it checked by an authorized dealer.<br />
Have it checked by an authorized dealer<br />
/ Pos:<br />
17. 3.8 Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Stark e Ersch ütte run gen (Vibri ere n) @ 0\m od_ 111 537 731 823 4_15 21. doc @ 190 0<br />
Extreme vibration Have it checked by an authorized dealer<br />
Pos:<br />
17. 3.9 / Inne nteil/St öru ngsu rsach en und der en Bes eitigu ng/Stö run gsta bellen elem ente /Schnitt uns aube r, R asen wi rd g elb, Be nzin @ 0\ mod _111 537 746 865 6_1 521. doc @ 18 98<br />
Unclean cut, lawn is yellow<br />
Pos: 17. 3.10 /Inn ent eil/Stör ungs ursac hen un d de ren B eseitig ung/St öru ngst abelle nele ment e/Auswu rf v ersto pft, B enzin, Tu rboSig nal @ 0\m od_ 112 790 809 5450 _15 21. doc @ 188 6<br />
Ejection blocked<br />
Pos:<br />
17. 3.11 /Inn ent eil/Stör ungs ursac hen un d de ren B eseitig ung/St öru ngst abelle nele ment e/Ge mulc hte G ras sieht s chlech t au s Hecka uswu rf @ 5\m od_ 1183 467 132 357 _15 21.d oc @ 359 50<br />
Mulched grass appearance is<br />
poor:<br />
clumps, excessive clippings,<br />
rough cut.<br />
Blade blunt. Have it sharpened and balanced by an<br />
authorized dealer Q .<br />
Cutting height too low. Adjust to higher cutting height I .<br />
Engine speed too low. Operate at max. rpm.<br />
Mowing too fast. Adjust mowing speed.<br />
Insufficient overlapping of cuts when Tall grass conditions may dictate that more<br />
mowing.<br />
overlapping of cuts is required.<br />
Lawn becomes matted. A lawn scarifier can remedy the problem<br />
considerably<br />
Turbo signal has not been detected<br />
J + K .<br />
Empty the grass collector L .<br />
Engine speed too low. Operate at max. rpm.<br />
Cutting height too low for grass that<br />
is too high.<br />
Adjust to higher cutting height I .<br />
Pushing mower too fast. Adjust mowing speed.<br />
Grass not dry. Let grass dry.<br />
Blade blunt. Have it sharpened and balanced by an<br />
authorized dealer.<br />
Mulching rule not followed (cut max. Adjust to higher cutting height I .<br />
1/3 of the grass height; the height of Convert mower to rear discharge U2 +<br />
the grass to be cut must be lower S1 and mow grass first with higher cutting<br />
than 10 cm)<br />
setting.<br />
Travel speed too fast. Adjust travel speed.<br />
Grass build-up under deck. Adjust to higher cutting height I .<br />
Insufficient overlapping of cuts when Tall grass conditions may dictate that more<br />
mowing.<br />
overlapping of cuts is required<br />
Grass not dry. Adjust to higher cutting height I .<br />
Let grass dry.<br />
Pos: 17. 4 /In nent eil/Stör ungs urs ache n un d d ere n Beseiti gung /Stör ungs ursac hen un d de ren B eseitig ung Text Benzin @ 0\ mo d_11 153 781 833 90_ 152 1.doc @ 1 905<br />
In case of faults and defects which have not been listed here, please contact the nearest authorized dealer.<br />
Repairs which require specialized knowledge should only be performed by a qualified expert. Your authorized dealer will<br />
naturally also be glad to help if you do not wish to perform the maintenance work described here yourself.<br />
=== = = E nde der Stückliste == == =<br />
18