EAD 200wi - Elcon Systemtechnik
EAD 200wi - Elcon Systemtechnik EAD 200wi - Elcon Systemtechnik
LED „WLAN“ (green): WLAN status ON WLAN activated OFF WLAN deactivated 24 EAD 200wi LED „LINK“ (green): Access network status ON Connection to Access Switch established FLASHES (discontinuously) in line with the bit clocking sequence FLASHES (at 1 Hz) Booting procedure or no link to the Access Switch (line interrupted, attenuation too high) LED „ 1“, „ 2“ (green): Status of the two analogue interfaces ON SIP-registration executed correctly, receiver hung up (on-hook FLASHES (at 4 Hz) SIP-registration is missing FLASHES (at 1 Hz) Telephone or other terminal unit is ringing OFF Receiver removed (off-hook)); no user configured by provider LED „ISDN“ (green): Status of the ISDN interface DSS1 protocol ON SIP-registration correctly executed, receiver hung up (on-hook) flashes at 4 Hz No SIP-registration executed flashes at 1 Hz Telephone or other terminal is ringing flashes (900 ms ON, 100 ms OFF) Receiver removed (offhook); no user configured by the provider OFF Line interruption 2.5 Cable connection 1. Connect the WAN-interface of the EAD 200wi with the access port of your network operator, using a standard Ethernet cable. 2. Link the EAD 200wi with the network interface card of the PC. For this, use an Ethernet cable and connect it to one of the „LAN“-marked RJ45-sockets on the EAD 200wi and to the RJ45-socket of the network interface card (see the related instructions). 3. Your analogue telephones, fax equipment, answering machines, tariff metering appliances, etc. shall be connected to one of the RJ11 sockets that are marked with the symbol „ “. 4. Connect your ISDN terminating equipment to the RJ45-socket marked „ISDN“. 5. Finally use the enclosed plug-in power supply module to connect the DC socket „ “ on the EAD 200wi to the electricity network. Do not use any other power supply module than the one included in delivery. The use of other power supply units will result in the loss of the CE conformance and exclude any warranty claims. 2.6 Putting into operation After application of the supply voltage and performed self-configuration the EAD 200wi is ready for work. The complete line between Access Switch and EAD 200wi will be put into operation by the network provider. It has a preset configuration or makes the required settings automatically by self-configuration. Version: 2012/06/06
EAD 200wi Prerequisite for proper operation of your data link via the EAD 200wi is the correct installation of the network interface card to your PCs. Detailed information on this should be received in the documentation provided by the card manufacturer. As the case may be, the following procedure should be executed for your PC configuration: 1. Start the PC. 2. Open network characteristics of your operating system. Windows ® 2000, XP: Start � Settings � Network Connections � Local Area Connection (Icon) � Properties of Internet Protocol (TCP/IP) to this link Windows ® 7: Start � Settings � Network- and Sharing center → Change adapter settings → Right mouse button click on Local Area Connection (Icon) → Properties → Double-click on Internet protocol version 4 (TCP/IPv4) 3. Select Obtain an IP address automatically for this link. Fig. 8: Selection of automatic allocation of IP-addresses 4. Acknowledge the change and restart your PC, if necessary. Your data transfer link is now ready for work. Further questions about configuration of your PC should be addressed to your Internet Service Provider. Version: 2012/06/06 25
- Seite 1 und 2: EAD 200wi Ethernet Access Device Ku
- Seite 3 und 4: EAD 200wi Safety precautions � Pl
- Seite 5 und 6: EAD 200wi Inhalt / Contents DEUTSCH
- Seite 7 und 8: EAD 200wi 2 Installation Bild 2: Bl
- Seite 9 und 10: EAD 200wi Pinbelegung der RJ45-Buch
- Seite 11 und 12: EAD 200wi Netzbetreiber in Betrieb
- Seite 13 und 14: EAD 200wi 2.9 Konfiguration der DIP
- Seite 15 und 16: EAD 200wi 3 Konfigurieren des EAD 2
- Seite 17 und 18: EAD 200wi Bild 12: Erweiterte Konfi
- Seite 19 und 20: EAD 200wi Bild 14: Ändern des WLAN
- Seite 21 und 22: EAD 200wi 5 Wichtige Hinweise 5.1 H
- Seite 23 und 24: EAD 200wi 2 Installation WLAN 802.1
- Seite 25: EAD 200wi Pin assignment of the RJ4
- Seite 29 und 30: EAD 200wi 2.9 Configuration of DIP
- Seite 31 und 32: EAD 200wi 3 Configuration of the EA
- Seite 33 und 34: EAD 200wi Figure 12: Advanced Setup
- Seite 35 und 36: EAD 200wi Figure 14: Changing the W
- Seite 37 und 38: EAD 200wi 5 Important notes 5.1 Man
- Seite 39 und 40: EAD 200wi Version: 2012/06/06 37
LED „WLAN“ (green): WLAN status<br />
ON WLAN activated<br />
OFF WLAN deactivated<br />
24<br />
<strong>EAD</strong> <strong>200wi</strong><br />
LED „LINK“ (green): Access network status<br />
ON Connection to Access Switch established<br />
FLASHES (discontinuously) in line with the bit clocking sequence<br />
FLASHES (at 1 Hz) Booting procedure or no link to the Access<br />
Switch (line interrupted, attenuation too high)<br />
LED „ 1“, „ 2“ (green): Status of the two analogue interfaces<br />
ON SIP-registration executed correctly, receiver hung<br />
up (on-hook<br />
FLASHES (at 4 Hz) SIP-registration is missing<br />
FLASHES (at 1 Hz) Telephone or other terminal unit is ringing<br />
OFF Receiver removed (off-hook)); no user configured<br />
by provider<br />
LED „ISDN“ (green): Status of the ISDN interface DSS1 protocol<br />
ON SIP-registration correctly executed, receiver hung<br />
up (on-hook)<br />
flashes at 4 Hz No SIP-registration executed<br />
flashes at 1 Hz Telephone or other terminal is ringing<br />
flashes (900 ms ON, 100 ms OFF) Receiver removed (offhook);<br />
no user configured by the provider<br />
OFF Line interruption<br />
2.5 Cable connection<br />
1. Connect the WAN-interface of the <strong>EAD</strong> <strong>200wi</strong> with the access port of your network<br />
operator, using a standard Ethernet cable.<br />
2. Link the <strong>EAD</strong> <strong>200wi</strong> with the network interface card of the PC. For this, use an Ethernet<br />
cable and connect it to one of the „LAN“-marked RJ45-sockets on the <strong>EAD</strong> <strong>200wi</strong><br />
and to the RJ45-socket of the network interface card (see the related instructions).<br />
3. Your analogue telephones, fax equipment, answering machines, tariff metering appliances,<br />
etc. shall be connected to one of the RJ11 sockets that are marked with the<br />
symbol „ “.<br />
4. Connect your ISDN terminating equipment to the RJ45-socket marked „ISDN“.<br />
5. Finally use the enclosed plug-in power supply module to connect the DC socket<br />
„ “ on the <strong>EAD</strong> <strong>200wi</strong> to the electricity network. Do not use any other power<br />
supply module than the one included in delivery. The use of other power supply units<br />
will result in the loss of the CE conformance and exclude any warranty claims.<br />
2.6 Putting into operation<br />
After application of the supply voltage and performed self-configuration the <strong>EAD</strong> <strong>200wi</strong> is<br />
ready for work. The complete line between Access Switch and <strong>EAD</strong> <strong>200wi</strong> will be put into<br />
operation by the network provider. It has a preset configuration or makes the required settings<br />
automatically by self-configuration.<br />
Version: 2012/06/06
Change language