Schneideinsätze A-CUT 3118 • Stückpreise bei Abnahme in VPE = 10 Stück je Größe und Qualität Vc/fz <strong>Drehen</strong> AIMC • Ab- und Einstechen • mit Spanbrecher • Schnittbreiten-Toleranz „W“ ± 0,1 mm ISO K N ISO P M K ISO P ISO P M Größe Bezeichnung W K Radius 355<strong>001</strong>.... 355<strong>001</strong>.... 355<strong>001</strong>... 355<strong>001</strong>... (Breite) (Grad) mm ..03 ..49 ..64 ..62 mm HW3410 HC3635 HC36<strong>30</strong> HC3540 unbeschichtet beschichtet beschichtet beschichtet 01.. AIMC 1.6 1,6 0º 0,16 7,40 – 9,70 – 04.. AIMC 2 2,2 0º 0,20 7,40 9,70 9,70 9,70 05.. AIMC 2 6L 2,2 6º 0,20 7,40 – 9,70 – 06.. AIMC 2 6R 2,2 6º 0,20 7,40 – 9,70 – 10.. AIMC 3 3,1 0º 0,20 7,40 9,70 9,70 9,70 11.. AIMC 3 6L 3,1 6º 0,20 7,40 9,70 9,70 9,70 12.. AIMC 3 6R 3,1 6º 0,20 7,40 9,70 9,70 9,70 13.. AIMC 4 4,1 0º 0,25 8,– 10,35 10,35 10,35 14.. AIMC 4 6L 4,1 6º 0,25 8,– – 10,35 – 15.. AIMC 4 6R 4,1 6º 0,25 8,– – 10,35 – 19.. AIMC 5 5,1 0º 0,<strong>30</strong> 8,65 11,10 11,10 – 20.. AIMC 5 6L 5,1 6º 0,<strong>30</strong> 8,65 – 11,10 – 21.. AIMC 5 6R 5,1 6° 0,<strong>30</strong> 8,65 – 11,10 – 22.. AIMC 6 6,4 0º 0,35 9,55 12,20 12,20 – 23.. AIMC 6 6L 6,4 6º 0,35 9,55 – 12,20 – 24.. AIMC 6 6R 6,4 6º 0,35 9,55 – 12,20 – AIMJ • Ab- und Einstechen • mit Spanbrecher • Schnittbreiten-Toleranz „W“ ± 0,1 mm ISO K N ISO P M K ISO P ISO P M Größe Bezeichnung W K Radius 355002.... 355002.... 355002.... 355002.... (Breite) (Grad) mm ..03 ..49 ..64 ..62 mm HW3410 HC3635 HC36<strong>30</strong> HC3540 unbeschichtet beschichtet beschichtet beschichtet 04.. AIMJ 2 2,2 0º 0,20 7,40 9,70 9,70 9,70 05.. AIMJ 2 6L 2,2 6º 0,20 7,40 9,70 9,70 9,70 06.. AIMJ 2 6R 2,2 6º 0,20 7,40 9,70 9,70 9,70 10.. AIMJ 3 3,1 0º 0,20 7,40 9,70 9,70 9,70 11.. AIMJ 3 6L 3,1 6º 0,20 7,40 9,70 9,70 9,70 12.. AIMJ 3 6R 3,1 6º 0,20 7,40 9,70 9,70 9,70 13.. AIMJ 4 4,1 0º 0,25 8,– 10,35 10,35 10,35 14.. AIMJ 4 6L 4,1 6º 0,25 8,– 10,35 10,35 – 15.. AIMJ 4 6R 4,1 6º 0,25 8,– 10,35 10,35 – 19.. AIMJ 5 5,1 0º 0,<strong>30</strong> 8,65 – 11,10 11,10 W R Neutral Links Rechts Vc/fz Technik-Handbuch Nr. 0199<strong>001</strong>0<strong>30</strong> oder www.sartorius-werkzeuge.de Neutral Links Rechts R K° AIPV • Präzisionseinstiche und <strong>Drehen</strong> (E-Ausführung, gerundet) • mit Spanbrecher • Schnittbreiten-Toleranz „W“ ± 0,02 mm ISO P M K ISO P M Größe Bezeichnung W Radius 355003.... 355003.... (Breite) mm ..49 ..62 mm HC3635 HC3540 beschichtet beschichtet 01.. AIPV 3.00E 0.40 3,00 0,40 11,20 11,20 02.. AIPV 4.00E 0.40 4,00 0,40 11,60 11,60 05.. AIPV 6.00E 0.40 6,00 0,40 15,20 – 06.. AIPV 3.00E 1.50 3,00 1,50 11,75 11,75 07.. AIPV 4.00E 2.00 4,00 2,00 12,60 12,60 09.. AIPV 6.00E 3.00 6,00 3,00 16,45 – AIPV • Präzisionseinstiche und <strong>Drehen</strong> (Seegerring) • mit Spanbrecher • Schnittbreiten-Toleranz „W“ ± 0,02 mm Größe Bezeichnung W Radius 355004.... 355004.... (Breite) mm ..49 ..62 mm HC3635 HC3540 beschichtet beschichtet 01.. AIPV 1.85 0.10 1,85 0,10 10,70 10,70 02.. AIPV 2.00 0.20 2,00 0,20 10,70 10,70 03.. AIPV 2.15 0.15 2,15 0,15 10,70 – 04.. AIPV 2.65 0.15 2,65 0,15 11,20 – 05.. AIPV 3.00 0.20 3,00 0,20 11,20 11,20 06.. AIPV 3.18 0.20 3,18 0,20 – 11,20 07.. AIPV 4.00 0.20 4,00 0,20 11,60 11,60 08.. AIPV 4.15 0.15 4,15 0,15 11,60 11,60 09.. AIPV 5.00 0.20 5,00 0,20 – 11,60 <strong>30</strong>-86 Preisangaben in Euro, zzgl. MwSt. ISO P M K ISO P M W R Artikel mit fettgedruckten Preisen = Lagerware
Schneidenträger zum Axialeinstechen A-CUT 3117 AH 106 R • zur Verwendung von Schneideinsätzen AIMF • zur Aufnahme in Spannschäften AGTBN • zur Bearbeitung von Durchmesser 35 - 700 mm Vc/fz Ausführung rechts Größe Bezeichnung Plattengröße Schneideinsatz Breite ØD T max A B1 L 354012.... AIMF W B min-max rechts mm mm mm mm mm mm mm AH 106R 3502 AH 106 35R-2 AIMF 2N 2,1 32 35- 46 20 5,2 0,8 150 138,90 4502 AH 106 45R-2 AIMF 2N 2,1 32 45- 61 20 5,2 0,8 150 132,25 6002 AH 106 60R-2 AIMF 2N 2,1 32 60- 80 20 5,2 0,8 150 132,25 8002 AH 106 80R-2 AIMF 2N 2,1 32 79-102 20 4,0 0,8 150 132,25 1002 AH 106 100R-2 AIMF 2N 2,1 32 101-132 20 4,0 0 150 132,25 7503 AH 106 75R-3 AIMF 3N 3,0 32 65- 92 20 5,2 1,0 150 132,25 9003 AH 106 90R-3 AIMF 3N 3,0 32 90-122 20 5,2 0,2 150 132,25 1203 AH 106 120R-3 AIMF 3N 3,0 32 120-160 25 5,2 0 150 132,25 8004 AH 106 80R-4 AIMF 4N 4,0 32 80-155 <strong>30</strong> 5,2 2,5 150 132,25 1504 AH 106 150R-4 AIMF 4N 4,0 32 150-500 <strong>30</strong> 5,2 2,5 150 132,25 8005 AH 106 80R-5 AIMF 5N 5,0 32 80-162 32 5,2 2,5 150 132,25 1505 AH 106 150R-5 AIMF 5N 5,0 32 150-600 35 5,2 2,5 150 132,25 9006 AH 106 90R-6 AIMF 6N 6,0 32 90-150 32 8,0 2,5 150 145,50 1506 AH 106 150R-6 AIMF 6N 6,0 32 148-700 35 5,2 2,5 150 138,90 <strong>Drehen</strong> Schneideinsätze zum Axialeinstechen A-CUT 3118 • Stückpreise bei Abnahme in VPE = 10 Stück je Größe und Qualität Vc/fz AIMF • AIMF-Einsätze sind nicht mit AIMC-, AIMJ- oder AIPV-Einsätzen austauschbar • Schnittbreiten-Toleranz „W“ ± 0,1 mm • Hinweis: Nach dem ersten Einstich kann die Einstichbreite in beide Richtungen vergrößert werden ISO P Größe Bezeichnung Ausführung W Radius Ø D 355005.... (Breite) (Bereich) ..49 mm mm mm HC36<strong>30</strong> beschichtet 04.. AIMF 2N neutral 2,1 0,20 ab 35 9,60 07.. AIMF 3N neutral 3,0 0,<strong>30</strong> ab 54 9,10 10.. AIMF 4N neutral 4,0 0,25 ab 35 10,25 11.. AIMF 5N neutral 5,0 0,25 ab 40 10,85 12.. AIMF 6N neutral 6,0 0,25 ab 44 11,90 Vc/fz Technik-Handbuch Nr. 0199<strong>001</strong>0<strong>30</strong> oder www.sartorius-werkzeuge.de Artikel mit fettgedruckten Preisen = Lagerware Preisangaben in Euro, zzgl. MwSt. <strong>30</strong>-87
- Seite 1 und 2:
Drehwerkzeuge Drehlinge HSS-Co10 Dr
- Seite 3 und 4:
Drehmeißel 3102 HSS-E DIN 4951- 49
- Seite 5 und 6:
HM-Innen-Eckdrehmeißel DIN 4974 -
- Seite 7 und 8:
Übersicht Klemmhalter ISO-Bezeichn
- Seite 9 und 10:
Klemmhalter, negativ PDJN • PDJN
- Seite 11 und 12:
Klemmhalter, negativ PSDNN • PSDN
- Seite 13 und 14:
Klemmhalter, negativ MWLN • MWLN
- Seite 15 und 16:
Klemmhalter, positiv SSSC • SSSC
- Seite 17 und 18:
Klemmhalter, positiv SVJB • SVJB
- Seite 19 und 20:
Bohrstange, negativ MTLN • MTLN R
- Seite 21 und 22:
Bohrstange, positiv SCLC • SCLC R
- Seite 23 und 24:
Bohrstangen, positiv SDUC • SDUC
- Seite 25 und 26:
Bohrstange, positiv STLC • STLC R
- Seite 27 und 28:
Modulares Bohrstangen-System 3129
- Seite 29 und 30:
Bohrstangenköpfe A 20 X SFN. 16 Au
- Seite 31 und 32:
ISO-Wendeschneidplatten CCET 80°-r
- Seite 33 und 34:
Spanbrecher MP 3108 F M R finishing
- Seite 35 und 36: Spanbrecher MP 3108 F M R finishing
- Seite 37 und 38: Spanbrecher RP 3108 F M R finishing
- Seite 39 und 40: Spanbrecher FT 3107 F M R finishing
- Seite 41 und 42: Spanbrecher MP 3108 F M R finishing
- Seite 43 und 44: Spanbrecher GS 3107 F M R finishing
- Seite 45 und 46: Spanbrecher PG 3107 F M R finishing
- Seite 47 und 48: Spanbrecher FT 3107 F M R finishing
- Seite 49 und 50: Spanbrecher RP 3108 F M R finishing
- Seite 51 und 52: ISO-Wendeschneidplatten VCMT 35° r
- Seite 53 und 54: ISO-Wendeschneidplatten WNMG 80° t
- Seite 55 und 56: Spanbrecher PG 3107 F M R finishing
- Seite 57 und 58: TCGT 60° dreikant, positiv 7°, Sp
- Seite 59 und 60: ISO-Wendeschneidplatten ALULine 310
- Seite 61 und 62: Vc/fz Technik-Handbuch Nr. 01990010
- Seite 63 und 64: ISO-Wendeschneidplatten PKD / CBN 3
- Seite 65 und 66: Klemmhalter 3112 Außengewinde •
- Seite 67 und 68: Bohrstangen 3112 Innengewinde • H
- Seite 69 und 70: Gewindeschneidplatten 3113 metrisch
- Seite 71 und 72: Gewindeschneidplatten 3113 metrisch
- Seite 73 und 74: Gewindeschneidplatten 3113 Vollprof
- Seite 75 und 76: Gewindeschneidplatten 3113 Vollprof
- Seite 77 und 78: Vollprofil UN (UNC, UNF, UNEF, UNS)
- Seite 79 und 80: Bohrstange MINI Innengewinde • Hi
- Seite 81 und 82: Gewindeschneid-Satz 3112 • gängi
- Seite 83 und 84: Stechdrehen mit A-CUT INFO Das A-CU
- Seite 85: Klemmhalter A-CUT 3117 AHR/L 211
- Seite 89 und 90: Das System INFO Mit dem D-Clamp Kle
- Seite 91 und 92: DFCP, rechtwinkelig • zum Axial-E
- Seite 93 und 94: DGP • für Seegerringe • zum Pr
- Seite 95 und 96: W Schneidenträger 3121 7° KGI W K
- Seite 97 und 98: Ersatzteile Klemmschraube Führungs
- Seite 99 und 100: Ein- und Abstechsystem für Außen-
- Seite 101 und 102: -MINI Radius-Einstechplatten (GR) 3
- Seite 103 und 104: s s s HM Schneidplatten MINI-CUT St
- Seite 105 und 106: e s e Rückwärtsdrehen (innen) •
- Seite 107 und 108: www.atorn.de Drehen Leistung brauch
- Seite 109 und 110: Klemmhalter mini-børe 3125 • mit
- Seite 111 und 112: Innenausdrehen und Fasen • ab Boh
- Seite 113 und 114: Schneidwerkzeugsätze mini-børe 31
- Seite 115 und 116: Klemmhalter zum Nutstoßen 3130 •
- Seite 117 und 118: Sets zum Nutstoßen von Längsnuten
- Seite 119 und 120: Rändelfräswerkzeug 3126 • Anwen
- Seite 121 und 122: 15 x 4 x 8 ( Ø x Breite x Bohrung