SPEciAL - ALU-WEB.DE
SPEciAL - ALU-WEB.DE
SPEciAL - ALU-WEB.DE
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
veransT alT ung<br />
88-97 GPa, tensile strength 186-197<br />
MPa), fracture toughness 6.4-6.5 MPa<br />
m 1/2 ) and even a hardness (4.9-5.1<br />
GPa) superior to that of conventional<br />
magnesium alloys.<br />
8. On the other hand, the microstructure<br />
of pressureless reactive sintered<br />
Mg 2 Si-TiC and Mg 2 Si-TiB 2 composites<br />
offers additional improvement<br />
in tensile properties (Young’s modulus<br />
132-157 GPa, tensile strength 477-564<br />
MPa) and hardness (9-10 GPa). Regarding<br />
the fracture toughness (1.4-2.3<br />
MPa m 1/2 ), this is significantly lower<br />
than in Mg-Mg 2 Si-TiC but still three<br />
to four times higher than the average<br />
reported values for as-cast Mg 2 Si.<br />
9. The results obtained clearly<br />
demonstrate that routinely performed<br />
pressureless infiltration or pressureless<br />
sintering resulted in samples with<br />
almost theoretical density, offering<br />
at the same time great flexibility in<br />
tailoring the desired combination of<br />
properties and with a great industrial<br />
potential for low-cost and highly productive<br />
fabrication.<br />
Euroguss 2010<br />
acknowledgement<br />
This work was supported by funding from<br />
the Public Agency for Research and Development<br />
of the Republic of Slovenia, as well<br />
as the Impol Aluminium Company and Bistral<br />
d.o.o. from Slovenska Bistrica, Slovenia,<br />
under contract No. 1000-07-219308.<br />
references<br />
Treffpunkt der Druckgussfachwelt<br />
Vom 19. bis 21. Januar 2010 trifft<br />
sich die internationale Druckgussfachwelt<br />
auf der Euroguss in<br />
Nürnberg. Drei Tage lang drehen<br />
sich die Gespräche auf den Messeständen<br />
der rund 300 Aussteller<br />
um Technik, Prozesse und Produkte<br />
im Druckguss. Etwa 6.000<br />
Fachbesucher werden erwartet.<br />
Parallel zur Fachmesse findet der<br />
Internationale Deutsche Druckgusstag<br />
mit einem umfangreichen<br />
Vortragsprogramm statt.<br />
Die Euroguss ist die größte Veranstaltung,<br />
die die gesamte Wertschöpfungskette<br />
beim Druckguss zeigt.<br />
Damit ist sie zugleich eine Plattform,<br />
um sich über aktuelle Trends und Entwicklungen<br />
der Branche auszutauschen.<br />
Gotthard Wolf, Geschäftsführer<br />
des Bundesverbandes der Deutschen<br />
Gießerei-Industrie (BDG), zeigt<br />
sich optimistisch für die Zukunft.<br />
1. K. U. Kainer, F. von Buch, In: Magnesium<br />
Alloys and Technology, Ed. K. U. Kainer,<br />
DGM, Wiley-VCH, 2003; pp. 1.<br />
2. F. Moll, K. U. Kainer, In: Magnesium Alloys<br />
and Technology, Ed. K. U. Kainer, DGM,<br />
Wiley-VCH, 2003; pp. 197.<br />
3. W. Blum, B. Watzinger, P. Weidinger, In:<br />
Magnesium Alloys and their Applications,<br />
Eds. B. L. Mordike, K. U. Kainer, Werkstoff-<br />
Informationsgesellschaft mbH, 1998; pp.<br />
49.<br />
4. H. Muramatsu, K. Kondoh, E. Yuasa, T.<br />
Aizawa, JSME, 46(3), (2003) 247.<br />
5. L. Lu, K. K. Thong, M. Gupta, Composite<br />
Science and Technology 63 (2003) 627-632.<br />
6. L. Wang, X. Y. Qin, W. Xiong, X. G. Zhu,<br />
Mater. Sci. and Eng. A 459 (2007) 216.<br />
7. J. M. Munoz-Palos, M. C. Cristina, P.<br />
Adeva, Mater. Trans. JIM 37 (1996) 1602.<br />
8. V. Milekhine, J. K. Solberg, M. I. Onsoen,<br />
International Journal of Materials Research<br />
„Auch wenn sich die Druckgussindustrie<br />
durch ihre<br />
Nähe zur Automobilbranche<br />
momentan in einer Talsohle<br />
befindet, bin ich mir sicher:<br />
Wir werden als Gewinner aus<br />
der Krise herausgehen“, sagt<br />
er. In den F&E-Abteilungen<br />
der Unternehmen werde mit<br />
Hochdruck daran gearbeitet,<br />
innovative Produkte zu entwickeln.<br />
Mittelfristig werde<br />
die Gießereibranche ihren<br />
Wachstumskurs fortsetzen.<br />
Auf dem Programm des<br />
Internationalen Deutschen<br />
Druckgusstages stehen 22<br />
Fachvorträge, die erstmals<br />
direkt in der Messehalle in<br />
einem Forum gehalten werden.<br />
Themenschwerpunkte<br />
sind „Werkzeuge und Maschinentechnik“,„Aluminium-,<br />
Magnesium- und Zink- Euroguss 2008<br />
12 (2003) 1331.<br />
9. V. Milekhine, M: I. Onsoen, J. K. Solberg,<br />
T. Skaland, Intermetallics 10 (2002) 743.<br />
10. K. Kondoh, H. Oginuma, T. Aizawa, Materials<br />
Transactions 42 (2001) 1293<br />
11. J. Zhang, Z. Fan, Y. Q. Wang, B. L. Zhou,<br />
Materials Science and Engineering A 281<br />
(2000) 104.<br />
12. R. Hadian, M. Emamy, N. Varahram, N.<br />
Nemati, Materials Science and Engineering<br />
A 490 (2008) 250.<br />
13. Q. D. Qin, Y. G. Zhao, P. J. Cong, Y. H.<br />
Liang, W. Zhou, Journal of Alloys and Compounds<br />
420 (2006) 121.<br />
14. J. Zhang, Z. Fan, Y. Q. Wang, B. L. Zhou,<br />
Scripta Mater., 42 (2000) 1101<br />
15. J. Qingxiu, Z. Caixia, H. Xiaodong, China<br />
Foundry 6 (2009).<br />
16. K. Kondoh, H. Oginuma, A. Kimura, S.<br />
Matsukawa, T. Aizawa, Materials Transactions<br />
45 (2003) 981.<br />
17. K. Kondoh, H. Oginuma, R. Tsuzuki, T.<br />
Aizawa, Materials Transactions 44 (2003)<br />
611<br />
18. G. H. Li, H. S. Gill, R. A. Varin, Metallurgical<br />
Transactions A 24 (1993) 2382.<br />
19. K. Niihara, R. Morena, D. P. Hasselman,<br />
J. Mater. Sci. Lett. 1 (1982) 13.<br />
20. In Carbide, Nitride and Boride Materials<br />
Synthesis and Processing, Ed. Alan W. Weimer,<br />
Chapman & Hall 1997, Appendix C.<br />
21. Yu. Ryabkov, P. Istomin, N. Chezina,<br />
Mater. Phys. Mech. (2001) 101.<br />
58 <strong>ALU</strong>MINIUM · 12/2009<br />
Messe Nürnberg