Elma BM811 Elma BM817 Elma BM515 - Elma Instruments
Elma BM811 Elma BM817 Elma BM515 - Elma Instruments Elma BM811 Elma BM817 Elma BM515 - Elma Instruments
Elma 811 + 817 + 515 side 69Relative mode (BM815 & BM817 only)Relative zero allows the user to offset consecutive measurements in the meter with the displayreading as the reference value. Practically all display readings can be set as relative reference valueincluding MAX/MIN feature readings. Press the button momentarily to activate and to exitrelative zero mode.Manual or auto-rangingPress the RANGE button momentarily to select manual ranging, and the meter will remain in therange it was in. The LCD annunciator turns off. Press the button momentarily again to stepthrough the ranges. Press and hold the button for at least 1 second to resume auto-ranging.Note: The manual ranging feature is not available in Hz function.Set beeper offPress the Hz button while turning the meter on to disable the Beeper feature.
Elma 811 + 817 + 515 side 70Data logging mode (BM511 & BM515 only)Press the Start button for at least 1 second to start “Strt” or to stop “StoP” data logging mode. Pressthe SELECT button momentarily to toggle the LCD display to the measuring data or the loggeddata item number.Press the Start button momentarily to pause or to continue. The LCD annunciator “H” will beflashing when paused.Note:1. When the logged data item number exceeds 9999 (where available), the bar chart will also beused to indicate the most significant digit of the item number in the order of 10000. That is 1 =10000, 2 = 20000, ... etc.2. When the memory is full, data logging mode will be stopped automatically, and the meter willthen enter APO mode.3. To guarantee the accuracy of all logged data, the meter will stop data logging mode when thebattery is low, and will revert to normal measuring mode.4. The data will be saved to non-volatile memory shortly after every measurement to maximizedata security. However, the end-of-data sign can only be stored after data logging is finished.Therefore, always “StoP” the data logging function before switching off the meter. After datalogging is finished, you can switch off the meter for transportation, storage, or even changingbattery.
- Page 19 and 20: Elma 811 + 817 + 515 side 184) Tryk
- Page 21 and 22: Elma 811 + 817 + 515 side 20Batteri
- Page 23 and 24: Elma 811 + 817 + 515 side 22Innehå
- Page 25 and 26: Elma 811 + 817 + 515 side 241.2 Ord
- Page 27 and 28: Elma 811 + 817 + 515 side 263 Instr
- Page 29 and 30: Elma 811 + 817 + 515 side 283.5 NMR
- Page 31 and 32: Elma 811 + 817 + 515 side 304.3 Tem
- Page 33 and 34: Elma 811 + 817 + 515 side 324.5 Aut
- Page 35 and 36: Elma 811 + 817 + 515 side 344.7 RS
- Page 37 and 38: Elma 811 + 817 + 515 side 364.11 Ho
- Page 39 and 40: Elma 811 + 817 + 515 side 384.15 St
- Page 41 and 42: Elma 811 + 817 + 515 side 40Bedienu
- Page 43 and 44: Elma 811 + 817 + 515 side 42• Bei
- Page 45 and 46: Elma 811 + 817 + 515 side 44Analog-
- Page 47 and 48: Elma 811 + 817 + 515 side 46Kapazit
- Page 49 and 50: Elma 811 + 817 + 515 side 48ΩWider
- Page 51 and 52: Elma 811 + 817 + 515 side 50µA-, m
- Page 53 and 54: Elma 811 + 817 + 515 side 52Hinterg
- Page 55 and 56: Elma 811 + 817 + 515 side 54Ausscha
- Page 57 and 58: Elma 811 + 817 + 515 side 56USER'S
- Page 59 and 60: Elma 811 + 817 + 515 side 58Measure
- Page 61 and 62: Elma 811 + 817 + 515 side 60Analog
- Page 63 and 64: Elma 811 + 817 + 515 side 62Capacit
- Page 65 and 66: Elma 811 + 817 + 515 side 64Ω Resi
- Page 67 and 68: Elma 811 + 817 + 515 side 66μA, mA
- Page 69: Elma 811 + 817 + 515 side 68Backlit
- Page 73 and 74: Elma 811 + 817 + 515 side 724) Pres
- Page 75 and 76: Elma 811 + 817 + 515 side 74Battery
- Page 77 and 78: Elma 811 + 817 + 515 side 76Safety:
- Page 79 and 80: Elma 811 + 817 + 515 side 78AC Curr
<strong>Elma</strong> 811 + 817 + 515 side 70Data logging mode (BM511 & <strong>BM515</strong> only)Press the Start button for at least 1 second to start “Strt” or to stop “StoP” data logging mode. Pressthe SELECT button momentarily to toggle the LCD display to the measuring data or the loggeddata item number.Press the Start button momentarily to pause or to continue. The LCD annunciator “H” will beflashing when paused.Note:1. When the logged data item number exceeds 9999 (where available), the bar chart will also beused to indicate the most significant digit of the item number in the order of 10000. That is 1 =10000, 2 = 20000, ... etc.2. When the memory is full, data logging mode will be stopped automatically, and the meter willthen enter APO mode.3. To guarantee the accuracy of all logged data, the meter will stop data logging mode when thebattery is low, and will revert to normal measuring mode.4. The data will be saved to non-volatile memory shortly after every measurement to maximizedata security. However, the end-of-data sign can only be stored after data logging is finished.Therefore, always “StoP” the data logging function before switching off the meter. After datalogging is finished, you can switch off the meter for transportation, storage, or even changingbattery.