NAD VISO 1 AP Wireless AirPlay Music System - Polaris Audio
VISO 1 REMOTE CONTROL ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ S Sequentially select through Sources. +/- Increase or decrease loudness level. X Temporarily mutes audio output or restores audio from mute mode. The following remote control commands are applicable only in AirPlay mode or when using an iOS device 0 Skip forward to the next song. Skip forward through parts of the current broadcast or song (if applicable). 9 Skip back to the previous song. Skip back through parts of the current broadcast or song (if applicable). uj Start playback. Pause playback temporarily. 6
VISO 1 AP OPERATION FIRST TIME USE Out of the box and connecting the VISO 1 AP to the mains power source for the first time, the “S” indicator will alternately switch to green and red light after initializing. This indicates that the VISO 1 AP is ready to be configured. Refer to the following sections to fully enjoy and appreciate your VISO 1 AP. 3 Launch Safari and enter http://192.168.1.12 . The VISO 1 AP User Interface menu window will appear. Select Profile Configuration. ENGLISH SETTING UP NETWORK CONNECTION AirPlay lets you stream music from your AirPlay-enabled device to the VISO 1 AP. The AirPlay-enabled device and the VISO 1 AP must be in the same network to send and receive streaming audio with AirPlay. The VISO 1 AP can be connected to a network using any of the following methods A Wired connection B Wireless connection C Share Wi-Fi setting Start playback of your device after successful network connection using any of the above methods. WIRED CONNECTION Network connection using Ethernet broadband connection. Set up a Wired Ethernet broadband router with broadband internet connection. Your router or home network should have a built-in DHCP server to consummate the connection. • Using a standard straight-through Ethernet cable, connect one end of the Ethernet cable (not supplied) to the LAN port of your wired Ethernet broadband router and the other end to VISO 1 AP’s LAN port. • The ”S” indicator will turn to solid green upon successful network connection. It is advisable that wired connection is utilized when possible. Wired connection is less likely to have “drop-out” or range problem and not vulnerable to interference or eavesdropping. WIRELESS CONNECTION Wireless (WiFi) broadband router with broadband internet connection is required for wireless connection to be established. Wireless connection for VISO 1 AP can be setup by the following procedure. 1 Press and hold “S” until it turns flashing green – this indicates it is in Access point/setup mode already. 2 Using your iOS device (iPad is used here for reference), select among the list of available network connections the unique network ID (NAD_ VISO1_DF601A in this example) of your VISO 1 AP. 4 Select your local network from the drop down SSID list (NADLAB (WPA2 TKIP+CCMP) in this example). NOTES • The Status Information displays current details about your VISO 1 AP like connection status, signal strength, firmware version and others. If your VISO 1 AP is configured already, locate and access the TCP/IP address of your VISO 1 AP to check Status Information. • Firmware Update is not for consumer use- this is restricted to authorized NAD service personnel and distributors. 5 Type the WPA Passphrase (if it is password protected) of your local network in the field provided and then select Apply to join in. NEDERLANDS DEUTSCH ITALIANO ESPAÑOL FRANÇAIS РУССКИЙ SVENSKA 7
- Page 1 and 2: ® Wireless AirPlay® Music System
- Page 3 and 4: 23. Battery Disposal - When disposi
- Page 5: IDENTIFICATION OF CONTROLS ENGLISH
- Page 9 and 10: VISO 1 AP OPERATION SOURCE SELECTIO
- Page 11 and 12: РУССКИЙ SVENSKA NEDERLANDS D
<strong>VISO</strong> 1 REMOTE CONTROL<br />
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ<br />
S<br />
Sequentially select through Sources.<br />
+/- Increase or decrease loudness level.<br />
X<br />
Temporarily mutes audio output or restores audio from mute mode.<br />
The following remote control commands are applicable only in <strong>AirPlay</strong> mode or when using an iOS<br />
device<br />
0 Skip forward to the next song.<br />
Skip forward through parts of the current broadcast or song (if applicable).<br />
9 Skip back to the previous song.<br />
Skip back through parts of the current broadcast or song (if applicable).<br />
uj<br />
Start playback.<br />
Pause playback temporarily.<br />
6
Change language